Subject: Hornet flies with the Rotamax 2 rotor
From: Rotary Engine
Date: 8/2/2008, 6:24 AM
To: AAA Put this in the To box




The Hornet guys got a few hours flying the 2 rotor Rotamax powered   airplane before departing to OSH. Unfortunately I did not get a video
yet. The muffler is half a spin tech and it is rather quiet.
The rubber gear box coupling was replaced with a 50 durometer version
down from the original 60 durometer version with a noticeable   reduction
in idle speed. 50 durometer is the lowest available for that brand
of coupling.  Like all geared 2 rotor aircraft engines they tend to
resonate around 1800 RPM. The quick and simple cooling system
worked great despite being installed BEHIND the cargo pad :)
That is the president of Hornet (Robert) removing the gear box  from  the engine.

Paul Lamar

The Hornet is a cute little airplane.  I can imagine having fun with
something like that.  I am surprised it is using the RotaMax two
rotor--as that seems like a lot of engine  for this aircraft.  But I
am just guessing what its hp/weight requirements might be.   So,   how
did it perform?   Two more observations:  first, that  narrow motor
mount will take some getting  used to. I would not be comfortable with
it.   And, secondly,  how big is the fuel tank?  I think the two rotor
will be thirsty.    Jerry


It was estimated at about 480 gallons an hour based on the half  gallon of fuel burned in 3.7 minutes. Not an accurate way of  measuring the fuel burn. A rather unlikely number in fact.
Something wrong there. Perhaps my notes are wrong.

The static RPM was about 5000 with a 1.9 gear box. From the Rotamax  web site: 4750 is about 100 HP. Engine weight claimed is 145 pounds.  Assuming it is 100 HP  a BSFC of .6 would be 60 pounds an hour or 10  gallons an hour. A much better guess. It is not like you are going  on long cross country flights with an LSA anyway so fuel burn is not  much of an issue. The claimed  engine weight is 145 pounds. The 80  HP Rotax 912 engine weighs 132 pounds. That is about 100 pounds less  than a Subaru.
The big advantage right at the moment is the cost.
It is about $5000 cheaper than a Rotax 912 I am guessing.

They also flew the airplane briefly direct drive with a max RPM of  3000. The power must of been down around 50 HP and that is how the  airplane flew. Like it had 50 HP. The Hornet has flown before
with low HP engines as it was close to an ultralight concept in it's  early days. In other words it has a lot of wing area for its weight.

Apparently, and as far as I can determine, the RPM, HP and therefore  the gear ratio is limited by the rotor needle bearings. Currently  they are using a composite needle cage which may be softening as the  rotor temperature is quite high. An easy change would be to use a  steel needle cage. Rotamax could easily test that hypothesis. The  loads on the rotor bearings are a minimum at 6000 RPM. If they can  get the RPM up to 6000 there should be another 20 HP available or  about 120 HP total. That would make it suitable for some  experimental aircraft. It would also make the
60 HP one rotor version more competitive with the 80 HP Rotax 912.  That should take another $5000 out of the cost of an LSA.

Paul Lamar

I think the fuel consumption stated in the first paragraph should work out to about 8 gph at 5000 rpm/100 hp.  Jerry



Lets see 60 minutes divided by 3.7 is about 16.2 So 16.2 times one half gallon is 8 gallons and hour. You are right Jerry. My mistake. So 8.1 gallons an hour is 48 pounds of fuel per hour. Ah so that is were the mistake is.  48.6 pounds divided by 100 HP is .486 BSFC. Rather good if it was actually making 100 HP.

Well hopefully we will have some more data when the Hornet guys
get back home to California.

BTW I'll bet Joy did the calcs :)

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.