Subject: NA 20B dyno curve
From: Rotary Engine
Date: 8/10/2008, 7:38 PM
To: AAA Put this in the To box


Paul,


My SeaWind friend just got his all alumium (except for the intermediate
housing) 20B with aggressive street ports and slightly enlarged exhaust
ports back from R.B.  He is considering the new PowerSport PSRU as it
is robust and three inches shorter than Tracy's combination.  I don`t
particularly like the reduction ratio of  2.42:1 as it would difficult
with his 76" to take advantage of the top rpm power.  Unless he pushes
his prop rpm over 2700 on T.O.  his engine will be hovering around 6500
rpm which is below peak hp.  Redline on a 20B was I believe was around
8000 rpm but max power was below that figure.

Do you or anyone have a dyno curve on a NA 20B at 6500 to 7000 rpm?   My
rough guess would be around  270 - 280 Hp.

We know turbocharged it put out max 320 Hp. As a contingency plan he
will slap a turbocharger on it.

Doug in Japan


It all depends on the intake manifold. What I have is on Al Gietzen's
intake manifold which is less than optimum. Notice haw the manifold air
pressure
starts to drop at 3000 RPM.

Paul Lamar

Paul--Al has done a great job but the data appears to again show the basic
limitation of side port configuration compared to a well configured
peripheral port arrangement.  We ran into this with the first prototype
engine which used dual side ports.  It made 200 hp @ 7,000 but the target
was that power at lower rpm for safety and durability.  We quickly realized
a ram tuned peripheral port would be much better by achieving the same h.p.
at a much lower rpm...same 200 h.p. was at 5,900 r.pm.

Steve Beckham.

------------------------------------------------------------------

I totally agree. I am amazed the sharp right angles in the side ports
makes so much difference. Apparently a lot of youtube viewers also
agree as we have had over 5350 hits on our youtube RX8 P-port "How to step
by step". It is running about 100 new hits a day. By far our most popular
youtube video. We discovered one can weld a SS tube to the steel liner real
easy :)
Ironically Mazda themselves could do it with out affecting the EPA smog
rules if they did it with a trap door p-port like this.

http://www.youtube.com/watch?v=LkKw72dZ2yc

Paul Lamar


Being that the new Mazda 16X (16B?) will be direct-injection, would
there be ANY emissions penalty for having peripheral ports? It might
provide a little internal EGR and lower HC emissions.

Having side ports in addition to a peripheral port would get in the
way of the elegant simplicity possible with a rotary. If it's possible
to do so with good port timing, a peripheral-only exhaust and intake
rotary with aluminum intermediate housings would pretty much be the
ideal experimental aircraft engine

-Chris

Well depends on what type of p-port. If it is open 100% of the time yes
there probably would be an emissions penalty. The excessive complication is a direct result of the current draconian car environment crafted by the "I hate cars" weenies. They would have us all living in ant hills taking public transportation. You might as well shoot yourself or stay drunk all the time :) See Bruce Briggs "The War Against the Automobile". We all better hope they don't target general aviation next.

IMHO the 16B is less than ideal as it is likely not as good from a power to weight ratio stand point than  say an all aluminum 13B. The 16X is a sledge hammer attempt to  improve the low RPM torque and still fit in an RX8. There is no replacement for displacement. It is diametrical opposite to the fine AIXRO kart engine geometry.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.