> >> Hey, guys,
> >>
> >> Here is an image of the Integrated Motor Assist (IMA) as installed on
> >> the Honda Insight.
> >>
> >>
http://www.beaudaniels.com/automotive-images/Insight-IMA.jpg
> >>
> >> The starter/motor is that 2-inch thick pancake electric motor sitting
> >> right between the inline-3 cylinder gasoline engine and the
> >> transmission. It is kind of hard to see. That is the largest image
> >> of it I have found so far.
> >>
> >> The IMA always worked for me in the year I owned an Insight. Honda
> >> does design good stuff, generally. Could the IMA fulfill the
duties you
> >> envision for an alternator/starter on an aircraft?
> >>
> >> Les Nordman
>
>
> There is a fundamental difference in technology here that has not been
> mentioned.
> The StAR starter/ alternator is just or starting the gas engine and
> generating ordinary 14v power.
> The IMA is an alternate power source to drive the car when the gas
> engine is not needed and is therefore a much larger unit.
> Hardly what we require in an airplane, as I see it.
>
> Dave McCandless
Dear Mr. McCandless:
You have just put your finger on a vital point and, perhaps, have opened
up an easier, better way for us to turbocompound our engines.
PROBLEM
One of the constant, large problems turbocompounding must overcome is
the problem of TIME. More specifically, "how do we get the power from
the turbocompounder to the propeller as quickly as possible?" Though
exhaust gasses blast out of the rotary engine at supersonic speeds, it
still takes time to turn that thermal and gas-speed (sorry, I don't know
a more precise term for it) energy into usable energy spinning the
propeller. So, specifically stated, the TIME problem for
turbocompounded aircraft rotary engines is: "We don't want to bog the
engine down, waiting for the turbocompounder to spin up to speed." The
usual way to solve this problem of conversion is mechanical: spinning
turbines, shafts, and gearboxes. More weight, more complexity, and less
reliability than the original rotary engine.
A SOLUTION
One solution is to Take The Problem Of Time Away.
What do I mean by that? Instead of trying to solve our time
problems with the turbocompounder shackled to the propeller
by mechanical means, how about let us
_decouple_ the power generation of
the turbocompounder from the power generation of the rotary engine?
Decouple those two power generations
_completely_.
GENERAL APPLICATION
Let the exhaust gasses blasting out of the rotary engine spin a turbine
which will turn an electrical generator. Make a
_SMALL_,
_LIGHT_ set of
batteries serve as the "automatic transmission" transferring power to
the propeller. The
_SMALL_,
_LIGHT_ set of batteries already have
been charged up from the previous flight. They are a reservoir of
power. Apply that reservoir of available power immediately to the
engine. The
_SMALL_,
_LIGHT_ batteries put the power of the
turbocompounder to the propeller at the same time as the rotary engine
does. This the batteries do until the turbocompounder is up to speed.
When the turbocompounder comes up to speed, let the power flow through
the batteries, to the IMA, to add turbocompounded horsepower to the e-shaft.
In all modes of use, the rotary engine is set free to make as much power
as it can to turn the propeller, with out worrying about, "when is the
power from the turbocompounder ever going to get here?" The
turbocompounder is set free to make as much power as it can, without
worrying about, "how can we get this power as quickly as possible to the
propeller?"
This process happens at idle,then when advancing the throttle to take
off and cruise settings. All the time. No dead weight.
SPECIFIC APPLICATION
In this particular application, with Honda's IMA under discussion, the
IMA could serve four purposes:
1. start the engine.
2. deliver stored power to the propeller, at start up and when throttle
settings change.
3. continue to deliver the power recovered by the turbocompounder,
_as_
it is recovered, to the propeller.
4. charge the
_SMALL,_ _LIGHT_ battery pack at the end of the present
flight, to be used at the start of the next flight.
That way, the IMA would be in constant use. It would never be dead
weight. This would handle the problem posed by Mr. McCandless: "The
IMA is an alternate power source to drive the car when the gas engine is
not needed and is therefore a much larger unit."
CAVEAT
You aviation powerplant types will, doubtless, point out many problems
with the
_specific_ _application_ to the problem. (MONEY! Yes, I know,
Mr. Lamar. So noted. :-) Problems, even insurmountable problems with
the application, are okay by me: I am not wedded to the Honda IMA, as
slick a piece of engineering as it is. Even if the Honda IMA does not
turn out to be the specific answer to our turbocompounding TIME problem,
I would like us to apply ourselves to the Principles:
1.
_Decouple_ the power generation of the rotary engine from the power
recovery of the turbocompounder
_completely_.
2. Apply the power recovered from the turbocompounder to the propeller
in a means
_better than_ mechanical connection:
a. electrical
b. hydraulic
c. some other amazing technology I have not even thought of.
CONCLUSION
The engineering giants of the 1950's gave us a wonderful tool:
turbocompounding. Let us stand on their shoulders.
Turbocompounding presents us with basic problems. One such problem is
TIME. Let us go farther than the giants of the 1950's could, rather
than just staying with their solutions. If we applied ourselves to
solving the basic problems turbocompounding presents us, we could create
a far better powerplant than by just massaging the solutions of the past.
Les Nordman
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.