> > To the Group:
> >
> > The following link shows a couple engines using compressed air for
> > fuel. I have also read an article about an Indian company doing the
> > same thing. Three different manufacturing companies in three different
> > parts of the world doing the same basic concept. Can anybody find
> > anything basically wrong with what they are doing? I know that the
> > Wankel is used as a compressor. If the air is reversed it could be used
> > as an engine.
> >
http://www.youtube.com/watch?v=yXrnCYAlUFc_
> > Norm DeBoer
>
>
> The advantage of fuel over batteries, compressed air
> and other fixed mass storage systems is that your
> weight decreases.
>
> How much does a carbon fiber air tank weigh and
> how much energy can you store in it?
>
> It might be good for a car where you can recover brake
> energy.
>
> Jeff Martin
>
> Fill your air compressor tank to 100 psi. Turn off the compressor.
> Time how long your air grinder runs. Another guess
> is it will run for about 5 minutes at the most. Multiply by 10 for
1000 PSI. 50
> minutes. Double the size of the tank. 1 2/3 hours or 100 minutes.
>
> My guess is an air grinder is 1 to 3 HP at the outside. 10 to 20
thousand RPM.
>
> Divide 50 HP by 3 HP or 16 times for the minimum HP needed for a
small car. So
> the car will run for 6.25 minutes. Triple that for 3000 psi. 18
minutes. I think
> you see where I am going with this.
>
> Paul Lamar
Air has weight, so at about 4000 psi, air weighs over 3 lb/gal. It will
also decrease in weight as it is consumed. A compressed air tank could
also be used as a supercharger without the hp drag of a supercharger for
a few minutes - like at takeoff. A very big advantage of this source of
pressurized air, is that it will come out of the high pressure tank at a
very cold temperature - the cooling of expansion instead of the heat of
compression like all superchargers and turbochargers. Therefore, no
intercooler would be necessary. A single tubular spar ala BD4 or
multiple tubular spars could serve as the compressed air tanks. When
carbon nanotubes with a tensile stress rating up to (at this time) 20
million psi are widely used, the compressed air tanks will be much
lighter and capable of much higher pressures.
Norm DeBoer
What does a scuba tank weigh? Welding tanks are not light weight.
A 230 HP engine uses 350 cubic feet per minute. Or 25 to 30 POUNDS
of air per minute.
Paul Lamar
--
Hi Paul,
Don't have my scuba tank wt handy but I've seen uncertifiable tanks cut
in half. The wall thickness is about one half inch. The garden
variety tank is cert'ed for 3000psi, requires hydrostatic re-test every
5 years at 5000 psi, and holds 94 cubic feet at 3000 psi. Some of the
wall thickness is probably due to the "abusive" environment the tanks
are exposed to but then again in a crash senerio a thinner wall just
makes better shrapnel from the explosion. Anyone even THINKING about
containing this kind of pneumatic pressure needs to go to the local
scuba shop and ask to watch a tank filling. In addition to all kinds of
checks and emergency relief valves the tanks are submerged in a water
bath to cool them and hydraulicly slow the shrapnel should a tank
explode ( a very rare occasion since the industry instituted the 5 year
retest). For wt purposes you could figure 29" tall, and 9" dia, and
spherical head both ends, and .5 wall times wt of alum. Dave M
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.