-------- Original Message --------
Subject: low-profile oil filter adapter block
Date: Tue, 02 Sep 2008 17:06:31 -0700
From: Rotary Engine
<rotaryeng@earthlink.net>
To: AAA Put this in the To box
<rotaryeng@earthlink.net>
Hi all,
Does anyone have a design for a low-profile adapter block to attach to
the oil filter mount, so a remote filter can be installed? Just curious
to know if I am reinventing the wheel or not.
Thanks much,
John Bell
Some body may have one of those but I don't know who. Jerry Hey could build it.
Here are some pictures. I'll ask Al Gietzen where he got his.
Paul Lamar
Paul,
I will assume the Renesis engine oil pump is significantly better
performing than the 1990? single turbo 13B if have. So how can I
upgrade the oil pump performance in my engine?
One option is to modify and bolt on the Renesis front housing
Second question. Racing Beat recommends when trying to boost a 13B to
power levels over 300hp that a second oil return line into the block be
added. Where would this second line be tapped into?
Doug in Japan.
There is nothing wrong with the 13B oil pump.
Especially the 3rd gen model. The 3rd gen turbo generated 280 HP stock.
You can actually reduce the oil temp by doing away with the right angle
from the pump out to the oil coolers. Some say as much as ten degrees. Any time
you are pumping fluid through a right angle you are adding heat. I think this
is the right place on the front end housing but you can tell by examining a
front end housings as the internal oil passages are obvious. This is as direct
out of the oil pump as you can get. Block off the old front cover outlet. Keep
the front oil pressure regulator in the system.
Don't use a pipe tap on the cast iron block. Too easy to crack the block.
Use a straight thread fitting with o-ring. Keep it the same size as the ID of
the oil cooler plumbing hose.
------------------------------------------------------
Here is an old message on the subject from Brian Cain.
-------- Original Message --------
Subject: Oil system modifications, was Front Cover O-ring/Low Oil Pressure
Nonsense (long)
Date: Tue, 11 Jan 2000 23:25:54 -0800
"Brian D. Cain" wrote:
>
> Everyone (and Tracy in particular),
>
> My second front cover o-ring job went well with excellent results.
> Per Tracy's suggestion, I left the gasket off and substituted it with
> Permatex Ultra Blue. As best I can tell, I have no visible oil leaks.
> I took the vehicle out for a spin and got the engine up to operating
> temperature (180F degrees water and oil temperatures in stop
> and go driving). Oil pressure, when cold was at 81psi up until about
> 110 to 120F degrees. At idle (1100rpm), the oil pressure was
> sustained right around 24 to 26psi at ~180F oil temperature,
> respectively. Everything seems a-ok there and will have an
> opportunity to put some real load on it tomorrow morning for that
> never-ending rat-race most of us call "work".
>
> Even though I spent nearly 5 hours working on this and it was a
> success, I'm very dissatisfied with the design of some of the oil
> system in general around the 13B. During my venting of frustration
> earlier this morning after learning that I would have to re-do a several
> hour job I did just two nights before, I got to talking to another racer
> friend of mine in the northern California area. He and I both got our
> lubrication diagrams out of the shop manuals. I spent half of the
> time complaining about this silly o-ring and how it's such a seemingly
> weak link in the chain of the most critical system in the engine itself.
>
> We discovered several things. For all of you guys who have some
> spare Mazda 13B front iron housings and front covers lying around,
> you may want to take a gander at this. It appears to be possible to
> run external oil lines, bypassing this front cover/front iron housing
> (and silly o-ring area) oil feed pretty much entirely by utilizing internal
> passages in the front iron housing that are already cast and available,
> albeit plugged up. Near the area of where the A/C and power
> steering bracket(s) would normally bolt on to the front cover and iron
> housing in the automotive setup, you'll notice two what I call "east/west"
> passages that are cast into the iron housing; one "south" and below
> the aforementioned (and thoroughly hated) front cover o-ring, and one
> above the o-ring, 90 degrees "east" of the front stationary gear.
>
> My idea, as was developed while talking to this friend of mine, was
> to plug the outlet at the front iron where the o-ring inserts, as well as
> the feed going down below it (elimination of factory oil metering pump
> oil supply here presumably), take advantage of this plugged shaft,
> tap it (or an adapter), and use it as the source oil feed to the oil
> cooler. This way, the o-ring (and passage through the front cover) is
> totally bypassed. I will probably go ahead with this during my 5th
> engine's rebuild. I don't ever want to deal with this absurdity of work
> ever again because of an o-ring the size of a dime.
>
> I went well further into this and suggested that even
> the feed going to the bottom corner of the rear iron be bypassed,
> along with relocation of the oil filter (and the elimination of those silly
> oil filter stand o-rings), and run a feed around the upper tubular dowel
> pins oil passage straight to this additional, upper cast passage to
> the front stationary gear (there's apparently a loss of oil at this point
> in some higher output engines) and turbocharger if necessary. The
> casting on the rear iron, where the oil filter stand would normally
> reside, would have to have to be tapped to accept an external line
> so an oil feed could be routed to the rear stationary gear and back
> of the eccentric shaft.
>
> (Side Note: Page 2-4 of the factory Rx7 shop manual, under the
> "Troubleshooting Guide", even though it's mentioned under the
> 'Oil Leakage' heading, the words "o-ring" nor "front cover" are
> mentioned under the 'Oil Pressure Drop' heading. Nice, huh?)
>
> Any thoughts, guys?
>
> B
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.