>>> Hi all,
>>> Does anyone have a design for a low-profile
adapter block to attach to
>>> the oil filter mount, so a remote filter can
be installed? Just curious
>>> to know if I am reinventing the wheel or not.
>>> Thanks much,
>>> John Bell
>>
>>
>> Some body may have one of those but I don't
know who. Jerry Hey could
>> build it.
>> Here are some pictures. I'll ask Al Gietzen
where he got his.
>>
>> Paul Lamar
>
>
> Paul,
>
> I will assume the Renesis engine oil pump is
significantly better
> performing than the 1990? single turbo 13B if have.
So how can I
> upgrade the oil pump performance in my engine?
> One option is to modify and bolt on the Renesis front
housing
>
> Second question. Racing Beat recommends when trying
to boost a 13B to
> power levels over 300hp that a second oil return line
into the block be
> added. Where would this second line be tapped into?
>
>
> Doug in Japan.
>
>
> There is nothing wrong with the 13B oil pump.
> Especially the 3rd gen model. The 3rd gen turbo
generated 280 HP stock.
>
> You can actually reduce the oil temp by doing away
with the right angle
> from the pump out to the oil coolers. Some say as much
as ten degrees.
> Any time you are pumping fluid through a right angle
you are adding
> heat. I think this
> is the right place on the front end housing but you
can tell by
> examining a front end housings as the internal oil
passages are
> obvious. This is as direct out of the oil pump as you
can get. Block
> off the old front cover outlet. Keep the front oil
pressure regulator
> in the system.
>
> Don't use a pipe tap on the cast iron block. Too
easy to crack the block.
> Use a straight thread fitting with o-ring. Keep it the
same size as
> the ID of the oil cooler plumbing hose.
>
> Paul Lamar
Hi Doug;
Paul has listed many of them.
Some common oil system modifications, most of these are
overkill unless
>8k rpm racing:
eshaft oil jet mod
thermal pellet replacement
front cover oring- replacement/fixes
pressure relief shim
oil pan baffling to help oil/air separation.
oil filter block-off - filter relocation
3rd gen/race pressure regulator
3rd gen/rx8 multi-window bearings
3rd gen irons/oil pump
block normal front cover oil discharge exit
drill and tap front iron main bearing feed tap
drill and tap a new, straight out oil discharge
oil pump passage modification to a smoothed kidney shape
dry sump setup
remove the oil filter screen (you must ensure that NOTHING
solid will be
sucked into the pump)
add a bell mouth to the oil pickup tube
align/enlarge bearing window to match galleries
gallery enlargement - 13B engines do not have as much meat
to bore out
the oil galleries as the 12a
Radical oil pedestal removal to shrink the engine.
Probably forgetting a few mods...
Here are a few pics of some common high power mods on
nopistons.com:
http://www.nopistons.com/forums/Oil-Pump-Mods-t51440.html
Do a few searches on oil system modifications. Lynn and
others have
provided a lot of info/pics.
Cheers
Cary
Cary
Can you elaborate on the purpose of the mod "drill and tap front iron main
bearing feed tap"? Is that the AN fitting in the lower front iron pic? What is
the blue AN fitting in the lower rear iron? Is that into the rear main feed
passage? After looking at the oil pump discharge passage, it appears the wall
thickness would not hold enough NPT threads. Is this outer wall machined away at
the corner so a straight fitting can be threaded into the direct passage to the
pump?
regards, Robert
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.