> >>> Hi all,
> >>> Does anyone have a design for a low-profile
> adapter block to attach to
> >>> the oil filter mount, so a remote filter can
> be installed? Just curious
> >>> to know if I am reinventing the wheel or not.
> >>> Thanks much,
> >>> John Bell
> >>
> >>
> >> Some body may have one of those but I don't
> know who. Jerry Hey could
> >> build it.
> >> Here are some pictures. I'll ask Al Gietzen
> where he got his.
> >>
> >> Paul Lamar
> >
> >
> > Paul,
> >
> > I will assume the Renesis engine oil pump is
> significantly better
> > performing than the 1990? single turbo 13B if have.
> So how can I
> > upgrade the oil pump performance in my engine?
> > One option is to modify and bolt on the Renesis front
> housing
> >
> > Second question. Racing Beat recommends when trying
> to boost a 13B to
> > power levels over 300hp that a second oil return line
> into the block be
> > added. Where would this second line be tapped into?
> >
> >
> > Doug in Japan.
> >
> >
> > There is nothing wrong with the 13B oil pump.
> > Especially the 3rd gen model. The 3rd gen turbo
> generated 280 HP stock.
> >
> > You can actually reduce the oil temp by doing away
> with the right angle
> > from the pump out to the oil coolers. Some say as much
> as ten degrees.
> > Any time you are pumping fluid through a right angle
> you are adding
> > heat. I think this
> > is the right place on the front end housing but you
> can tell by
> > examining a front end housings as the internal oil
> passages are
> > obvious. This is as direct out of the oil pump as you
> can get. Block
> > off the old front cover outlet. Keep the front oil
> pressure regulator
> > in the system.
> >
> > Don't use a pipe tap on the cast iron block. Too
> easy to crack the block.
> > Use a straight thread fitting with o-ring. Keep it the
> same size as
> > the ID of the oil cooler plumbing hose.
> >
> > Paul Lamar
> Hi Doug;
> Paul has listed many of them.
>
> Some common oil system modifications, most of these are
> overkill unless
> >8k rpm racing:
>
> eshaft oil jet mod
> thermal pellet replacement
> front cover oring- replacement/fixes
>
> pressure relief shim
> oil pan baffling to help oil/air separation.
> oil filter block-off - filter relocation
> 3rd gen/race pressure regulator
>
> 3rd gen/rx8 multi-window bearings
> 3rd gen irons/oil pump
>
> block normal front cover oil discharge exit
> drill and tap front iron main bearing feed tap
> drill and tap a new, straight out oil discharge
> oil pump passage modification to a smoothed kidney shape
>
> dry sump setup
>
> remove the oil filter screen (you must ensure that NOTHING
> solid will be
> sucked into the pump)
> add a bell mouth to the oil pickup tube
>
> align/enlarge bearing window to match galleries
> gallery enlargement - 13B engines do not have as much meat
> to bore out
> the oil galleries as the 12a
>
> Radical oil pedestal removal to shrink the engine.
>
> Probably forgetting a few mods...
>
> Here are a few pics of some common high power mods on
> nopistons.com:
>
http://www.nopistons.com/forums/Oil-Pump-Mods-t51440.html
> Do a few searches on oil system modifications. Lynn and
> others have
> provided a lot of info/pics.
>
> Cheers
> Cary
>
>
> Cary
Can you elaborate on the purpose of the mod "drill and tap front
iron main
bearing feed tap"? Is that the AN fitting in the lower front iron
pic? What is
the blue AN fitting in the lower rear iron? Is that into the rear
main feed
passage? After looking at the oil pump discharge passage, it appears
the wall
thickness would not hold enough NPT threads. Is this outer wall
machined away at
the corner so a straight fitting can be threaded into the direct
passage to the
pump?
regards, Robert
racingbeat.com sells an oil filter bypass block part #11822. It does
use 2 o rings. I drilled and tapped 1/8"npt for a temperatire sender
John Prendergast
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.