Subject: Down side to blocking oil supply to front cover.
From: Rotary Engine
Date: 9/4/2008, 4:34 AM
To: AAA Put this in the To box


            > Hi Doug;
            > Paul has listed many of them.
            >
            > Some common oil system modifications, most of these are
            > overkill unless
            >   >8k rpm racing:
            >
            > eshaft oil jet mod
            > thermal pellet replacement
            > front cover oring- replacement/fixes
            >
            > pressure relief shim
            > oil pan baffling to help oil/air separation.
            > oil filter block-off - filter relocation
            > 3rd gen/race pressure regulator
            >
            > 3rd gen/rx8 multi-window bearings
            > 3rd gen irons/oil pump
            >
            > block normal front cover oil discharge exit
            > drill and tap front iron main bearing feed tap
            > drill and tap a new, straight out oil discharge
            > oil pump passage modification to a smoothed kidney shape
            >
            > dry sump setup
            >
            > remove the oil filter screen (you must ensure that NOTHING
            > solid will be
            > sucked into the pump)
            > add a bell mouth to the oil pickup tube
            >
            > align/enlarge bearing window to match galleries
            > gallery enlargement - 13B engines do not have as much meat
            > to bore out
            > the oil galleries as the 12a
            >
            > Radical oil pedestal removal to shrink the engine.
            >
            > Probably forgetting a few mods...
            >
            > Here are a few pics of some common high power mods on
            > nopistons.com:
            > http://www.nopistons.com/forums/Oil-Pump-Mods-t51440.html
            > Do a few searches on oil system modifications.  Lynn and
            > others have
            > provided a lot of info/pics.
            >
            > Cheers
            > Cary
            >
            >
            > Cary

           Can you elaborate on the purpose of the mod "drill and tap front
           iron main
           bearing feed tap"? Is that the AN fitting in the lower front iron
           pic? What is
           the blue AN fitting in the lower rear iron? Is that into the rear
           main feed
           passage? After looking at the oil pump discharge passage, it
     appears
           the wall
           thickness would not hold enough NPT threads. Is this outer wall
           machined away at
           the corner so a straight fitting can be threaded into the direct
           passage to the
           pump?

           regards, Robert

     In the picture, I have drawn in the upper dowel gallery used in the
     stock engine, and the dowels are lined with threads. The gold boss
     fitting labeled "oil in" is a new installation. The brass plug in the
     gallery end is drilled out, the face of the casting is milled flat then
     drilled and tapped for a straight thread and a chamfer for an "O" ring
     seal. The straight threads adds little stress to the casting. This
     location provides a straight shot into the front main bearing, and more
     than doubles the cross section of runners feeding the front main. The
     dowel gallery is left as stock. This fitting is fed oil from the new
     block on the filter stand, through a dash 10 AN hose.

     The stock oil out fitting in the aluminum front cover is plugged. The
     "O" ring junction is used with the stock "O" ring but a sheet stock disc
     is fitted under the "O" ring. So there will be no "O" ring failures with
     loss of pressure. You may also just fit a disc slightly taller than the
     "O" ring and install that to block the hole with no "O" ring at all.

     There is a very small gallery into the front cover to feed the OMP. If
     you plan to use it, no changes are made. You can leave the OMP (Oil
     Metering Pump) in place and remove the snap rings and drive gear.
     It can be reactivated at any later time if you like.

     The lower gold fitting is the new oil out location direct from the
     pressure side pump cavity. Again this must be a tube to boss with an "O"
     ring as above. An NPT might work well enough, but there is a danger of a
     cracked casting when the tapered pipe threaded fitting is tightened.

     The blue tube to boss at the lower rear is just replacing the stock
     banjo fitting.

     Lynn E. Hanover


     Well done Lynn. I might add with the original set up there is not
     one but
     about 3 or 4 sharp right angles. At 30 gallons an hour out of the pump
     that creates a lot of heat in the oil and makes the pump work harder
     than
     it needs to.

     -------------------------------------------------

     I just found another good picture on the subject.
     This is a pipe tap but what you want is a straight thread tap.

Paul Lamar


More on gallery locations and the faulty "O" ring junction.

Lynn E. Hanover


There is a down side to blocking oil to the front cover.
There is an oil control valve in the front cover. Both RX8 and 3rd gen as well as a larger version in the 2nd gen 13B. The function of this may be to protect
the oil pump and oil pump drive under very cold conditions. The oil may
be almost congealed and the high load on the pump chain drive and oil pump itself  may damage them. Racers never race in 20 degrees below zero so be aware of this potential problem if you block oil to the front cover.

Now you might ask how does blocking the front cover oil outlet to the oil coolers differ from extremly cold conditions. Good question. The answer is you are providing another outlet to the oil coolers from the oil pump on the left side of the front end housing.

Also of course don't forget to remove the oil metering pump and mix 2 cycle oil with the fuel.

Don't confuse this valve with the oil pressure regulator valve at the rear of the engine.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.