> GREG FLEMING wrote:
>> Forgive me if this has been discussed before, but does anyone see
merit
>> in using the Evans NPG waterless coolant?
>> http://www.evanscooling.com/main21.htm
>> Since this liquid's boiling point is much higher than regular 50/50
>> water/glycol, there is no boiling, meaning no pressure in the cooling
>> system. No pressure from steam, that is. Not as much pressure on the
>> hoses, clamps, fittings, etc. Also appears to give better cooling
>> properties.
>> Anyone heard of this stuff?
>> Greg in Canada
>
> People have tried it and it seems to work. In theory the conductivity
> between metal and coolant is not as good as metal to glycol and water.
>
> Paul Lamar
Paul, this stuff appears to be basic propylene glycol. Back in the day
when
we heard Dow was testing propylene glycol but not offering it
commercially,
Everett talked to some of their research folks who provided us a drum for
flight testing our prototype rotary engines. An interesting feature was
that it was biodegradable.
Our goal was to reduce or eliminate nucleate boiling around the spark plug
bosses in the rotor housings during sustained high power settings. As I
remember, we started these tests in the late 1980's. In addition to
propylene we also tested various other water/anti-freeze combinations and
no
pressure system, low and high pressure systems. Ultimately we settled on
what for us proved to work as the most superior cooling
combination--straight water with a small bottle (6-8 oz?) of Water Wetter
(or equivalent). The Water Wetter really helped reduce nucleate boiling
around the spark plug bosses. We settled on this combination with a
moderate pressure cap. The specs below may not be spot on but should be
close. I don't have my published charts handy listing all the
specifications for various cooling media but you probably have already
provided these. Oil listed here because at the time we nosing around
whether it would be possible to use oil cooling for a direct drive, 100
hp,
oil cooled version of our aluminum engine.
Thermal conductivity
Water = .343
Propylene Glycol = .173
Ethylene Glycol = .153
Oil = approx .08-.1
Specific Ht
Water = 1
Ethylene Glycol/water 50-50 = .825
Propylene glycol = .8
Ethylene Glycol 100% = .65
Steve Beckham
Hi, Steve:
Interesting read about your testing back in the late 80's. I guess this
is a classic exercise in compromise. I can't use straight water as a
coolant in Canada since it would freeze half of the year. Was there any
data to support a 50/50 mix of water and _Propylene_ Glycol instead of
water/ethylene? I like the bio-degradable part, and the propylene
appears to have an edge with thermal conductivity.
The Red Line's Water Wetter came in with pretty good marks in this
report from 'Turbo':
http://www.turbomagazine.com/features/0703_turp_cooling_system_additives/index.html
The 2 page article sure clears up a lot of mystery for me about coolant
and additives. I'm going to check out running a propylene/water mix
with additive. A good 'Canadian winter' approach.
Greg in Canada
Water Wetter exist because racing organization do not allow any kind of
Glycol
as it makes the track slippery when it spills.
Pure Ethylene Glycol is not used in engines because it actually has a
higher
freezing point. Excerpt from my book.
"The freezing point of pure water is higher than some winter temperatures,
and
its boiling point is lower than the coolant temperature at which a hot
(but not
overheated) engine can operate. Ethylene Glycol has a higher boiling point
than
water. This is especially an advantage on today's hotter running vehicles
with
multiple accessories and air conditioning. One drawback to using 100%
Ethylene
Glycol is that Ethylene Glycol does not absorb as much heat as water does.
Another is that the freezing point will actually be higher when the
ethylene
glycol concentration is too high. Ethylene Glycol is mixed with water
until it
is the correct concentration. The factory radiator fill is usually about
50%
water and 50% Ethylene Glycol, which provides protection against freezing
down
to -34 F. The freezing point of a mixture with a 70% concentration of
ethylene
glycol would be -85 F. Its boiling point of 235 F is 11 F higher than
would be
provided by a 50-50 mixture. A 70% concentration is the maximum that
should be
used."
Extra aircraft recommends changing the coolant ratio twice a year in the
liquid
cooled Continental engine.
"The development of the exact shape of the internal water jacket around
the
Wankel combustion chamber is still in a state of change after 40 years of
development as more and more power is extracted from the rotary. Some
turbo
charged Mazda rotary engines used in drag racing cars burning alcohol and
nitrous oxide are generating up to 400 HP per rotor or 800 HP for a two
rotor
engine. Several modifications have been tried such as grooving the walls
of the
water jacket to improve the heat transfer from the metal to the liquid
coolant.
See Figure M 1 on the next page."
"We have discovered that this is unnecessary if you limit your engine to
around
240 HP for take off and cruise at 200 HP. However this feature may come in
handy
in the future when we get more experience with higher HP turbo charged
Mazda two
and three rotor engines in aircraft use. Particularly when air racing
rotary
powered airplanes. BTW a P-port, 215 HP 2 rotor powered Velocity aircraft
averaged 205 MPH in a 500 mile cross country air race in Augast 2007.
We do know the two rotor Mazda engine will currently generate about 200 HP
continuously with out melting or cracking"
The full power metal temperatures in the hottest parts of the rotor
housing are
actually about 100 F below the typical air cooled aircraft engine.
Mark Steitle is currently running thermocouples in his three rotor...
rotor
housings and is reporting no excessive temperatures.
Paul Lamar
Good background Paul.
Regarding the rotor cooling issue, on all the original Powersport
prototypes, we found it necessary to add extra cooling capability and
turbulent flow around the spark plug bosses for sustained high power
settings and max power climbouts. Before we did it, we would get coking on
the inside of the rotor housing but we were changing so many variables at
the time, who knows the degree to which the mod alleviated that problem.
We shared this experience and the modifications with the Mazda factory guys
when they visited in the late 1980's/1990. When the third gen turbo engines
later came out they used a little bit of this modification around the spark
plug boss--appeared to be a simple mill cut. But we found it took more than
that to work meaningfully for sustained output rather than the compartively
short duty full power cycle seen in auto applications. We used the
Bridgeport and some hand work to do the mod. Probably was not even new at
the time and it or something akin was probably already in use by Jim D,
Roger M, Jim at RB, Mazdatrix and all other folks who have done serious
rotary engine development work. Don't remember, but it may have been Roger
who initially passed on the tip. He was always helpful in areas such as
this, and with other technical data r.e. oil correction factor/bob weights
for balancing, exhaust, etc. Also assume what we did and passed on was
reasonably copied on all the "new" Powersport engines at Raytech and I think
you told me the Velocity engine experience you cite was one of these.
Greg, thanks for the background piece. As I remember for winter operation
or extended flight at high alttitudes below freezing we settled on a
solution of propylene/water/water wetter combination. But always swapped
it out for straight water/Water Wetter as soon as conditions permitted.
Steve Beckham.
All new rotor housings have the mill mod.
I think coking on the rotor housing wear surface is caused by that crap in the
crankcase being used to lube the apex seals. I have been using Mobil 1 in my
rotaries for years and I see no ill effects. About five years ago we did a
simple test. Put a teaspoon full of oil in a cat food can and bake it for a half
hour at 500 F. You will be amazed at the difference in oils. Mobile one was head
and shoulders above mineral oils and not quite as good as turbine oil.
Now we have Idemitsu rotary engine oil available from Mazdatrix. Especially
formulated for the rotary. That should solve the problem forever.
Rotary Performance
311 E. Buckingham Rd
Garland, TX 75040
Email: sales@rx7.com
Phone: 972-530-3335
Fax: 972-414-2779
Website: www.rx-7.com
RotorSports Racing
465 Russell Farm Rd.
Kannapolis, NC 28081
Email: info@rotorsportsracing.com
Phone: 704-933-6222
Website: www.RotorSportsRacing.com
G&S Racing
460 N.W. 68th Ave.
Ocala, FL 34482
Phone: 352-237-7955
Fax: 352-237-7955
AIM Tuning
298F Gasoline Alley
Indianapolis, IN 46222
Email: info@aimtuning.com
Phone: 317-381-0898
Website: www.aimtuning.com
Apollo America Corporation
2041 Rosecrans Ave. #355
El Segundo, CA 90245
(310) 563-1930
E-mail us at sales@idemitsu-usa.com
Hours of Operation:
7AM - 4:30PM PST Monday thru Friday
Paul Lamar
--
Steve,
Sounds like the weakest link in the engine is the area around the spark
plugs.
I am working on designing a leading dual plug insert that can bolted to
the outer housing along with water seal and then TIG welded on the
inside elongated axial hole. I plan to have it constructed on the
school's CNC out of Stainless 303 and multi-grooved all surface that
contacts the coolant. It will have a hole for a temp. probe but now I
am wondering if I should plan for a water fitting as well:)
I want about 300Hp out of my boosted 13B for at least 5 minutes on
takeoff and 200 to 210Hp. for continuous long distance cruise. These
figures neccessitate getting serious cooling happening.
I am searching all possible way to increase coolant flow and heat
transfer as well as taking RB advice about grooving the water housings
on the hot side. Running E-85-E90 also cools the engine 100 degrees F.
but don't know how that effects heat transfer around the plugs. For
water cooling I think I have gone overboard with a K&W rammed air feed
feeding a dual pass heat exchanger (each 1.7 inch thick) and a total of
over 900 cubic inches excluding end tanks. Oil heat exchangers are two
20B units) totaling about 375 cubic inches of capacity.
The bottleneck as you well know is the rear rotor housing seeing higher
water temps. I hope I can mitigate that by moving more coolant through
the engine with a better water pump, though the ultimate answer for the
Mazda two rotor engine is a redesign in where they introduce the water
in and remove it. Something more akin to the four rotor technique
perhaps?
Have you given any thought at Power Sport to redirect the coolant via the
intermediate housing axially outwards?
Doug in Japan
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.