Subject: Coolant/rotor housings for aircraft rotary
From: Paul Lamar
Date: 9/19/2008, 6:37 AM
To: AAA Put this in the To box


Hi, Steve:

Interesting read about your testing back in the late 80's.  I guess
this
is a classic exercise in compromise.  I can't use straight water as a
coolant in Canada since it would freeze half of the year.  Was there
any
data to support a 50/50 mix of water and _Propylene_ Glycol instead of
water/ethylene?  I like the bio-degradable part, and the propylene
appears to have an edge with thermal conductivity.

The Red Line's Water Wetter came in with pretty good marks in this
report from 'Turbo':
http://www.turbomagazine.com/features/0703_turp_cooling_system_additives/index.html

The 2 page article sure clears up a lot of mystery for me about
coolant
and additives.  I'm going to check out running a propylene/water mix
with additive.  A good 'Canadian winter' approach.

Greg in Canada

Water Wetter exist because racing organization do not allow any kind
of
Glycol
as it makes the track slippery when it spills.

Pure Ethylene Glycol is not used in engines because it actually has a
higher
freezing point. Excerpt from my book.

"The freezing point of pure water is higher than some winter
temperatures,
and
its boiling point is lower than the coolant temperature at which a hot
(but not
overheated) engine can operate. Ethylene Glycol has a higher boiling
point
than
water. This is especially an advantage on today's hotter running
vehicles
with
multiple accessories and air conditioning. One drawback to using 100%
Ethylene
Glycol is that Ethylene Glycol does not absorb as much heat as water
does.
Another is that the freezing point will actually be higher when the
ethylene
glycol concentration is too high. Ethylene Glycol is mixed with water
until it
is the correct concentration. The factory radiator fill is usually
about
50%
water and 50% Ethylene Glycol, which provides protection against
freezing
down
to -34 F. The freezing point of a mixture with a 70% concentration of
ethylene
glycol would be -85 F. Its boiling point of 235 F is 11 F higher than
would be
provided by a 50-50 mixture. A 70% concentration is the maximum that
should be
used."

Extra aircraft recommends changing the coolant ratio twice a year in
the
liquid
cooled Continental engine.

"The development of the exact shape of the internal water jacket
around
the
Wankel combustion chamber is still in a state of change after 40 years
of
development as more and more power is extracted from the rotary. Some
turbo
charged Mazda rotary engines used in drag racing cars burning alcohol
and
nitrous oxide are generating up to 400 HP per rotor or 800 HP for a
two
rotor
engine. Several modifications have been tried such as grooving the
walls
of the
water jacket to improve the heat transfer from the metal to the liquid
coolant.
See Figure M 1 on the next page."

"We have discovered that this is unnecessary if you limit your engine
to
around
240 HP for take off and cruise at 200 HP. However this feature may
come
in
handy
in the future when we get more experience with higher HP turbo charged
Mazda two
and three rotor engines in aircraft use. Particularly when air racing
rotary
powered airplanes. BTW  a P-port, 215 HP 2 rotor powered Velocity
aircraft
averaged 205 MPH in a 500 mile cross country air race in  Augast 2007.
We do know the two rotor Mazda engine will currently generate about
200
HP
continuously with out melting or cracking"

The full power metal temperatures in the hottest parts of the rotor
housing are
actually about 100 F below the typical air cooled aircraft engine.

Mark Steitle is currently running thermocouples in his three rotor...
rotor
housings and is reporting no excessive temperatures.

Paul Lamar



Good background Paul.
Regarding the rotor cooling issue, on all the original Powersport
prototypes, we found it necessary to add extra cooling capability and
turbulent flow around the spark plug bosses for sustained high power
settings and max power climbouts.  Before we did it, we would get coking
on
the inside of the rotor housing but we were changing so many variables
at
the time, who knows the degree to which the mod alleviated that problem.

We shared this experience and the modifications with the Mazda factory
guys
when they visited in the late 1980's/1990.  When the third gen turbo
engines
later came out they used a little bit of this modification around the
spark
plug boss--appeared to be a simple mill cut.  But we found it took more
than
that to work meaningfully for sustained output rather than the
compartively
short duty full power cycle seen in auto  applications.  We used  the
Bridgeport and some hand work to do the mod.  Probably was not even new
at
the time and it or something akin was probably already in use by Jim D,
Roger M, Jim at RB, Mazdatrix and all other folks who have done serious
rotary engine development work.  Don't remember, but it may have been
Roger
who initially passed on the tip.  He was always helpful in areas such as
this, and with other technical data r.e. oil correction factor/bob
weights
for balancing, exhaust, etc.  Also assume what we did and passed on was
reasonably copied on all the "new" Powersport engines at Raytech and I
think
you told me the Velocity engine experience you cite was one of these.

Greg, thanks for the background piece.  As I remember for winter
operation
or extended flight at high alttitudes below freezing we settled on a
solution of  propylene/water/water wetter combination.  But always
swapped
it out for straight water/Water Wetter as soon as conditions permitted.

Steve Beckham.

All new rotor housings have the mill mod.

I think coking on the rotor housing wear surface is caused by that crap
in
the
crankcase being used to lube the apex seals. I have been using Mobil 1
in
my
rotaries for years and I see no ill effects. About five years ago we did
a
simple test. Put a teaspoon full of oil in a cat food can and bake it
for
a half
hour at 500 F. You will be amazed at the difference in oils. Mobile one
was head
and shoulders above mineral oils and not quite as good as turbine oil.

Now we have Idemitsu rotary engine oil available from Mazdatrix.
Especially
formulated for the rotary. That should solve the problem forever.


 Rotary Performance
311 E. Buckingham Rd
Garland, TX 75040
Email: sales@rx7.com
Phone: 972-530-3335
Fax: 972-414-2779
Website: www.rx-7.com

RotorSports Racing
465 Russell Farm Rd.
Kannapolis, NC 28081
Email: info@rotorsportsracing.com
Phone: 704-933-6222
Website: www.RotorSportsRacing.com

G&S Racing
460 N.W. 68th Ave.
Ocala, FL 34482
Phone: 352-237-7955
Fax: 352-237-7955

AIM Tuning
298F Gasoline Alley
Indianapolis, IN 46222
Email: info@aimtuning.com
Phone: 317-381-0898
Website: www.aimtuning.com

Apollo America Corporation
2041 Rosecrans Ave. #355
El Segundo, CA 90245
(310) 563-1930

E-mail us at sales@idemitsu-usa.com

Hours of Operation:
7AM - 4:30PM PST Monday thru Friday

Paul Lamar
--

Steve,

Sounds like the weakest link in the engine is the area around the spark
plugs.

 I am working on designing a leading dual plug insert that can bolted to
the outer housing along with water seal and then TIG welded on the
inside elongated axial hole.  I  plan to have it constructed on the
school's CNC out of Stainless 303 and multi-grooved all surface that
contacts the coolant.  It will have a hole for a temp. probe but now I
am wondering if I should plan for a water fitting as well:)

I want about 300Hp out of my boosted 13B for at least 5 minutes on
takeoff and 200 to 210Hp. for continuous long distance cruise. These
figures neccessitate getting serious cooling happening.

I am searching all possible way to increase coolant flow and heat
transfer as well as taking RB advice about grooving the water housings
on the hot side. Running E-85-E90  also cools the engine 100 degrees F.
but don't know how that effects heat transfer around the plugs.  For
water cooling I think I have gone overboard with a K&W rammed air feed
feeding a dual pass heat exchanger (each 1.7 inch thick) and a total of
over 900 cubic inches excluding end tanks.  Oil heat exchangers  are two
20B units) totaling about 375 cubic inches of capacity.

The bottleneck as you well know is the rear rotor housing seeing higher
water temps. I hope I can mitigate that by moving more coolant through
the engine with a  better water pump, though the ultimate answer for the
Mazda two rotor engine is a redesign in where they introduce the water
in and remove it.  Something more akin to the four rotor technique
perhaps?

Have you given any thought at Power Sport to redirect the coolant via
the
intermediate housing axially outwards?


Doug in Japan


Doug:  Since I sold Powersport after Everett died, I am not affiliated
with
the "new" Powersport-- called Powersport Aviation.

Regarding your other points, our last prototype alumuinum engine used a
version of the configuration you describe.  It introduced cooled water
into
the engine at the spark plug bosses via an aluminum billet manifold/jet
assembly bolted to the assembled power section housings that was sealed
with
o rings. I provided a photo of this engine earlier.  It went with the
company assets as part of the sale.  If you don't have a copy let me know
and will see if I can get you some including the engine installed in the
RV-3. That engine was indexed 90 degrees with the spark plugs facing
upward.
The cooling injector manifold/inlet  was a truss-like component that
provided some stability to the engine as well.  If my memory serves
correctly, the LeMans Mazda engine used a similar approach with a carbon
piece bolted to the assembled housings to provide added rigidity the the
engine while providing a place to bolt on various electrical components.
Our approach appeared to work but introduced excessive complexity and
cost.
The pieces and machining were simply too costly, and together with the
torsional absorbers on the eccentric shaft, added excessive costs to the
engine that were simply too great to be passed on in a production version.
We went to all this trouble because based on our work up to that point
that
indicated the limiting sustained power output of the engines was due in
large part to the heat flux in the region of the spark plug bosses.
Another
factor was the lack of stability of our aluminum side housings.

The kind of power you are talking probably will undoubtedly be a learning
experience and a resource-burner on many levels.  The closest we came to
your projected output was using nitrous for the 1997 Sun'n Fun
time-to-climb
competition in the unlimited class using our first Mazda two rotor
conversion engine prototype installed in Allan Tolle's RV-3.  The engine
was
rated at 200 horsepower normally aspirated and with the nitrous system we
produced approx. 350 h.p.    The qualifying was from a standing start to
2000 feet.  We qualified #1, ahead of Dave Morss in the Thunder Mustang,
Jeff Ackland in the Legend and Tom Hann in the Steward S-51.  We toasted a
reduction gear bearing in that qualifying session.  The bearing worked
when
the engine was normally aspirated and 200 h.p.  Although we managed to win
our class in the Sun 100 cross country race the next day, the damaged
bearing precluded competing in the finals for the time-to-climb.  We
should
have been very competitive. For more background about this refer to Jack
Cox's report in Sport Aviaion, August 1997 beginning on page 43. I mention
this because our 350 horsepower output was for seconds rather than minutes
or hours. Based on our experience, it will be a challenge to reliably
sustain 300 h.p. in an aircraft application with the basic two rotor for
sustained periods.

For reference regarding alternative coolant routing, it is interesting to
look a the work of Curtiss-Wright, Mercedes and also the work on
circumferential rotor housing cooling by NSU and Citroen with cool water
introduced  first into the rotor housings.  And Ford's stillborn rotary
program was seriously looking at this approach as well.  Somewhere we have
an internal engineering report given to us by one of the folks involved
with
the rotary project there.  I think the date was cica 1970.

Paul--regarding oils, from the very start we always used oil pre-mixed in
the fuel; never did use sump oil.  We tested a panopoly of different oils
mixed with the fuel, including Unocal AirKool and many other two stroke
motorcycle race oils.  Like you, found synthetic oil superior in every
respect except cost.  We were using Torco MPZ Synthetic at the end because
it worked and they were a sponsor when I raced cars.  But Mobil 1 is
indeed
very good.  Idemitsu was not available at the time, or at least we were
not
aware of it if it were.  Thanks again for the amazing resources you are
providing rotary folks.  I have been working on induction projects the
last
several days and your nicely consolidated references are terrific.

Steve Beckham.

Steve do you have any metal temperature data within one mm or so near the
combustion chamber of the area just below the lower spark plug?


Paul Lamar

Steve,

Thanks for your report.  Everett and your team pioneered a lot of the
work I am only now attempting and I am very grateful to see you sharing
this information.   It appears sustaining 300hp for even  5 minutes of
Take off and climb is challenging but perhaps the real challenge will be
sustaining cruise climb power (250 hp) for the thirty or more minutes it
will take to get to high altitudes when very heavy.   Cooler fuels and
turbo-compounding may be the only way to do it.
Trouble is turbo compound works best when the plane is at high altitudes.
Getting there is the challenge.

Yes I would like to see a close up picture of how you injected cool water
into the plug boss area.
I have room for a PT 1/8  fitting and thus can direct a 6mm channel of
cool water through my insert if necessary.  Sorry no illustration.  My
Windoz computer locked up on me in the middle of using Rhino yesterday
and now even the track pad and key board doesn't function:(]

 I choose stainless 303 after abandoning the idea of O-rings on the
inner housing.  I felt aluminum wouldn't survive being on that front
face and as for stainless, I was concerned about the machining precision
that is needed on the elongated  dual plug hole insert.  The fit would
have to be a perfect interface or blow by or hot gases would hit the
O-rings and moments later the water jacket.  The inner liner near the
plugs is a tough area to expect O-rings to survive and not expand with
the heat.  This leaves  TIG welding a similar alloy to the inner liner.
It is not my most favorite option but it may be the only option as the
aluminum housing will expand faster than the insert.  The inner liner
which appears to be non magnetic may be also be a 303 alloy.  I`m not
sure of this fact but it makes sense as 303 it is easier to machine and
shape yet retains some of the corrosion resistance compared to 304.

One question Steve.  Besides being the origin of the flame front, what
other factors contribute to the high temperatures at the leading plugs? I
wonder if higher exhaust gas pressures might be pushing hot gases
back into the relatively low pressure intake cycle as the apex seal
crosses the spark plug void.  The relatively small 5 mm hole water
passages don't help a bit either.

Doug in Japan




The Rotary Engine NewsLetter. Powered by Linux
ACRE NL web site. http://www.rotaryeng.net Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.




Doug--It will be a while before I can go back and get you some good photos
of the SuperLight engine showing various phtos of the the cooling
inlet/manifold at the spark plugs.  Also, somewhere in the file I should
have shop drawings of it as well. Regarding photos, I recently copied most
of the Iron Eagle/Mazda Conversion Engine photos from slides/transparencies
taken between 1995-1998 to electronic form to help us with present efforts
to clone that engine for baseline testing.  But have yet to organize and
copy to electronic form all the slides in the photographic files for the
earlier prototype engines.  I've been asked to work on organizing that stuff
from all years by a guy interested in writing a book about that work but
don't honestly know if I'll get the time it will take to do it all and get
anything else done.  As to details, given the march of time it has been so
long that  I've forgotten much of it and our record-keeping was not as good
as it should have been.  But I'll see what I can drag out for you.

Steve Beckham


Steve


Thanks.  No rush.

Doug in Japan





-- 
The Rotary Engine NewsLetter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net Youtube key word UTUBPLEASE Copyright 1998-2008 All world wide rights reserved.