Subject: Rotary engine for extreme altitude
From: Rotary Engine
Date: 9/22/2008, 3:27 AM
To: AAA Put this in the To box


>
> After much research and following the list discussion for the
> past several
> months, it's been determined that the rotary engine is our best,
> lightestand cost effective solution to an engine for an extreme
> altitude powered
> parachute. The payload is a manned suborbital spacecraft.
>
> There are a few different questions below. I appreciate advice,
> comments,and suggestions. Please contact me as well if you are
> interested in
> participating in the engine building. We are looking for
> partners, seasoned
> veterans... for this part of the program.
> ---------------------------
>
>
> What is the nominal (no turbo boost) Hp output from a single
> rotor section.
> I imagine this varies between the different models. I've seen
> figures of 50
> Hp through 150 Hp for a single rotor but not sure of what model
> it refers
> to?
>
> This ultimately leads to a question I have as to how many rotors
> one can
> linear gang together if you want very large Hp output.
>
> We have a near term need for a 300 to 600 Hp engine (300 Hp if
> we use two
> engines separately and 600 Hp if we only use one).
>
> The Hp output is at sea level with no turbo boost.
>
> The application is a powered parachute with a heavy lift
> capability (about
> 7000 lbs gross lift).
>
> The first target altitude is 35,000 ft then 40,000 ft - 50,000
> right up
> through 65,000 ft.
>
> Obviously as the altitude gets higher additional turbo charging
> will be
> necessary. We need to keep the cost reasonably under control on
> the engine
> building i.e. not a grass roots engine development program budget.
>
> We want to use existing rotary engines with COTS turbos and
> control software
> / hardware already developed for altitude compensation -
> integrating all
> together.
>
> Reliability is important as always in aviation as this is a manned
> application, however the powered parachute by definition already
> has the
> parachute deployed should there be an engine failure at any altitude.
>
> Some facts and figures we are aware of:
>
> A 5000 lb gross weight UAV powered parachute has flown to 50,000
> ft. The
> engine was a 250 Hp diesel (Delta hawk - heavy!) super charged
> and turbo
> charged. The engine power output was 60% at 35,000 ft and 40% Hp
> at 50,000
> ft.
>
> The manufacturer recommended to us that we should have higher
> overall Hp for
> a 50,000 ft plus altitude with 500 total Hp at sea level for a
> 5000 lb gross
> vehicle and 60% and 40% respectively.
>
> For our 7000 lb gross weight we believe we need 600 Hp at SL and
> between 25%
> to about 40% Hp at 50,000 ft depending on which numbers one believes.
>
> 65,000 ft would be in the 50% to 60% Hp range plus.
>
> One of the earlier UAV's (regular wings) used a triple turbo
> charged 100 Hp
> Rotax to achieve 65,000 ft. It's power output at 65,000 ft was
> 100%. The
> high aspect ratio wing and lower overall drag helped to achieve
> this low
> overall Hp need. The gross weight was about 2500 lbs.
>
> Longer term we are looking to use LNG (liquid methane) as the
> fuel - must
> also run on regular gas for ferry purposes.
>
> Phase 2 is a 3000 Hp engine SL with about 60% plus power output
> at 65,000
> ft.
>
> Phase 3 is a 6000 Hp engine SL with about 60% plus power output
> at 65,000
> ft.
>
> Overall that's a lot to chew on. All inputs and guidance
> apreciated. Thanks
> for taking the time to review.
>
> Cheers,
> Brian
> --------------------
>
> Brian Feeney
> DreamSpace and The da Vinci Project
> bfeeney@davinciproject.com
> http://www.davinciproject.com
>
> One rotor Mazda HP depends mostly on porting and manifold
> design. A P-port is the best. See:
> http://www.youtube.com/watch?v=LkKw72dZ2yc
>
> Four rotors on one e-shaft seems to be the upper limit.
> 600 HP for a normally aspirated (NA) four rotor is doable.
> Higher HP if turbo charged. Up to 1600 HP. Cooling is critical.
> I recommend buying this book. http://www.rotaryeng.net/cooling.html
>
> For certified rotaries see http://www.mistral-engines.com/
>
> Paul Lamar Back in the U.S.

Hi Brian,

You might find this interesting.  A rotary engine at 30,000ft
http://www.bmaa.org/upload/flo/fo1007.pdf  scroll down for full story

Marc
Montreal, Canada

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.