Subject: Cooling design for a Renesis in a Glass Goose
From: Rotary Engine
Date: 10/12/2008, 9:18 AM
To: AAA Put this in the To box


Paul  the photos you included in the last message were the 13b engine.  I
presently have the Renesis engine flying.  Not satisfied with the cooling
system -- yet.  With the 13b engine, I would say that the cooling was
acceptable for my area (cool weather),  could not use full power for long
on
takeoff.

A photo of the Renesis installation.   Notice the air flow restriction
behind the front rad. even without an alternator -- not much space for air
flow around the engine.

Rino


That prop extension you have on there is a real positive factor Rino IMHO.
That
moves the prop back away from the pylon which is a good thing
aerodynamically.
In theory one could reduce the angle of the sides of the pylon and give
perhaps enough room to get some ducts down to feed the internally mounted
rads. The wing would have to be trimmed aft of the spar. What diameter
prop are
you running? Two blade or 3 blade?

BTW Sandy, here are a bunch of dwgs that might help you out. I am not sure
where
these came from so whoever sent them thanks. Since it is a turbo it my be
Rino dwgs.

Paul Lamar

Paul,

The first 3 drawings are partly mine -- been modified and the others are not
mine but interesting.

A photo looking at the front of the cowling -- air intake.

Do you think that area should cool 180 hp --- with a good airflow.   I know
it does not have a very good airflow at the moment.  The air flow can be
improved and will be improved, I am working on that.

I get about  136 sq. in. area.   60 sq. in. for the front mounted rads, and
38 sq. in. for the oil cooler (inside the pylon) on the left side and 38 sq.
in. for one water rad (in the pylon) on the right side.  The water rad that
is inside the pylon has a 10" dia. Spal fan that draws 15 amps @ 14 volts.
I never run out of cooling on the ground with that but I do not know how
useful it is in the air.

I calculated the air exit area to about 200 sq. in. total.   The pylon is
open at the back, 2' wide full length, included in the calculated air exit
area.

In the photo, the scoop on top is the throttle body air intake.

I cannot run the Renesis full power for a long period before the oil gets to
220 deg. F  but I can run it all day at 6000 rpm and less in our cool
weather (about 65 deg. F daytime).   Water temp runs at about 195 deg F.

The prop. is a Warp Drive 65.5" dia. presently set at 17 deg. at 3/4 radius.
The prop. extension is 6" long.

I should get some data on the engine performance soon.  As an example I get
100 mph at 5100 rpm, OAT 60 deg. F.  alt 1600, egt 1670, map 21.7, fuel burn
5.0 gph U.S..   Aircraft gross weight is about 1450 lb.  Have not done much
testing yet.  Mostly getting used to the aircraft and practicing my
landings.

Rino

Nice looking airplane Rino.

What you have going for you is the weather up in Canada. Down here where
it gets to 110 F in the summer it is a whole nother thing. One degree F lower
ambient temperature is about a  one percent improvement in cooling.

Thanks for the numbers. At 100 MPH side rads are not going to add much drag.
Five U.S. gallons an hour is only about 60 to 70 HP.

What would help the oil temperature during take off is a larger oil pan.
My 230 HP O-470 has 12 U.S. quarts.

Paul Lamar

Paul,

I enlarged the oil pan so I can use 6 quarts, no room for more expansion
under the engine.
I should mention that my fuel flow gauge is not yet completely calibrated,
it is getting close.

This morning I flew a few circuits, OAT 37 deg. F
I could use full power for much longer, could probably keep full power to
altitude but did not try it, I wanted to practice my landings.
Full power gave:  rpm 6400, MAP 29.6, fuel burn 10.8, climb speed 100,
vertical speed 1500 fpm

Rino

Good numbers. 10.8 GPH is about 135 to 145 HP.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.