Subject: Steam cooling the turbine.
From: Rotary Engine
Date: 10/13/2008, 7:48 PM
To: AAA Put this in the To box


>   > I just found this paragraph in my new turbine book I
> bought in London.
>   > "Gas Turbine Engineering Handbook" Boyce. Third
> edition. 2006
>   >
>   > Here is the quote.
>   >
>   > "The new gas turbines being designed for the new
> millennium are
>   > investigating
>   > the use of steam as a cooling agent for the first and second
>   > stages of the
>   > turbines. Steam cooling is possible in the new combined cycle
>   > power plants,
>   > which is the base of most of the new high performance gas
>   > turbines. Steam, as
>   > part of the cooling as well as part of the cycle power,
> will be
>   > used in the new
>   > gas turbines in the combined cycle mode. The extra power
>   > obtained by the use of
>   > steam is the cheapest MW/$ available. The injection of
> about 5%
>   > of steam by
>   > weight of air amounts to about 12% more power. The
> pressure of
>   > the injected
>   > steam must be at least 40 Bar above the compressor discharge.
>   > The way steam is
>   > injected must be done very carefully so as to avoid
> compressor surge.
>   > These are not new concepts and have been used and
> demonstrated  > in the past.
>   > Steam cooling for example was the basis of the cooling
> schemes  > proposed by the
>   > team of United Technology and Stal-Laval in their conceptual
>   > study for the U.S.
>   > Department Of Energy study on the High Turbine Temperature
>   > Technology Program,
>   > which was investigating Firing Temperatures of 3000
> degrees F
>   > 1649 °q, in the
>   > early 1980s."
>   >
>   > I had already considered this in 2005 for the turbo
> compound rotary
>   > when I found out it is being done in bottoming cycle power
>   > plant gas turbines. I did the attached 3D to show how
> it could work.
>   >
>   > This is a further increase in the efficiency of the turbo
>   > compound Wankel
>   > engine. Might as well put all that exhaust heat to work.
>   >
>   > Development of the R3350 Turbo Compound Engine 1954 SAE
>   > Transactions. I had no
>   > idea, prior to 2005, when I first read this paper, that
> so much
>   > kinetic energy
>   > was wasted by the exhaust valves in a piston engine turbo
>   > compound. Need I
>   > mention yet again... the Wankel rotary has no exhaust
> valves ?
>   >
>   > Paul Lamar
>
> I would like to see/read more on this subject.
>
> Marc Joseph
>
> Engines of this type are known as bottoming or combined
> cycle engines and are widely used in stationary gas turbine
> electric power plants. Waste heat from the turbine is used
> to generate steam which drives a steam turbine. They are
> also highly efficient getting as much as 50% of the energy
> in a pound of fuel.
>
> We convert the un recovered heat to steam and inject it
> into the turbine. We then condense the steam in the exhaust
> back into water down stream. We might need to carry a bit
> of make up water.  Gas turbines according to Marks approach
> 60% over all efficiency. The steam can be injected back into
> the same turbine. No second turbine required.
>
> No additional weight except for a steam pipe in the exhaust
> pipe and a condenser. The condenser's job is to convert what
> is left of the steam in the exhaust back into water. The
> left over heat in the exhaust (900 F) after some of it has
> been extracted by the turbine will convert the water in the
> pipe into steam.
>
> Is this what you had in mind Marc?
>
> Paul Lamar

Hi Paul,

Yes I have saved the pdf file.  Gee you are reading my mind with your
second message by including the file :))

I see two aspect to compouding a rotary engine.

1.  Use your present research with the exhaust energy
2.  Use the heat lost in the exhaust

I sent you a link from a Cyclone engine.  For me it was a way to
influence the group to consider steam for compounding the rotary.  If
the group could set a goal on combining the two source of energies wasted.

One thing I have in my mind is this.  A turbo that produces electricity
versus pushing air in the air intake.  At the other end of the turbo an
element (like in an oven) could heat a small boiler.  Inside the boiler
an heat exchanger extracting the wasted heat.  All this steam/pressure
could be directed to a turbine attached to the Eshaft.  Et voilà!  A
turbo compounding rotary engine à la Pépé la pew :))

Oh well!  Just dreaming wide awake

Marc Joseph

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.