Subject: Aluminum rotors in charge cooled engines and the NTSB.
From: Rotary Engine
Date: 10/21/2008, 10:21 AM
To: AAA Put this in the To box


   OK. So for the sake of discussion, what happens if you take one of
   those single rotor 55 hp wankels from Renntech and go with the BE/AL
   rotor. They already run at about 10-5 or 11 grand. What kind of
   output are we looking at? 110 hp? Can you cool it? How about
   bearings? I agree that you can create a light-weight powerplant
   with high power density. What I worry about are cooling and
   silencing issues. The 65 hp Rotamax Wankels require a 32-36 inch
   stainless exhaust pipe before you get to the muffler. You're going
   to have to gear it. How much does the expense of the reduction unit
   go up with the increase in rotor rpm? What is the cheapest way to
   do a technology demonstrator? They already use Wankels for drone
   engines. I wonder if DARPA would be interested in a techology
   demonstrator engine(s)? They might also be interested in a compound
   version - high output and lower fuel consumption.

   best,

   george W.

   I think you mean AIXRO rotary kart engines. Renntech is just the U.S.
   distributor for those kart engines. All bets are off as that is a
   charged cooled
   engine. Charged cooled rotors typically run 650 F or higher. I don't
   have any
   specific data on the AIXRO rotor temperature but I am willing to bet
   they have
   not measured it yet. It is a real instrumentation challenge to
   measure the rotor
   temperature with slip rings and all that stuff.

   IMHO you need an oil cooled rotor to make Be/Al rotors work.
   I am not a fan of charged cooled rotors. If it were me I would copy
   Mazda's oil
   cooled rotors for all rotary engines except for the cheapest low
   duty versions.

   Where did you hear that about the Rotamax muffler? Rotamax engines
   have run with
   much shorter exhaust pipes. Come to think of it I have not heard
   from them since
   they crashed the Sadler. Also a charged cooled rotor design.

   Paul Lamar

   ------------------------------------------------------------------------
   NTSB Identification: CHI08LA274
   14 CFR Part 91: General Aviation
   Accident occurred Wednesday, September 03, 2008 in Findlay, OH
   Aircraft: Sadler Vampire, registration: N333SV
   Injuries: 1 Minor.

   This is preliminary information, subject to change, and may contain
   errors. Any
   errors in this report will be corrected when the final report has
   been completed.

   On September 3, 2008, at 1257 eastern daylight time, a Sadler
   Vampire, N333SV,
   received substantial damage on impact with terrain during a forced
   landing. The
   airplane experienced a total loss of engine power after takeoff from
   Findlay
   Airport, Findlay, Ohio. Visual meteorological conditions prevailed
   at the time
   of the accident. The 14 CFR Part 91 test flight was not operating on
   a flight
   plan. The pilot sustained minor injuries. The local flight was
   originating at
   the time of the accident.

   ------------------------------------------------------------------

   I found some correspondence between Rotamax and a European firm.
   Rotamax indicated the 32-36 inch exhaust length before the muffler.
   They implied that thicker stainless wall was preferable and that
   using insulating tape near the exhaust manifold was useful.  Also
   found a preliminary report from a college engineering project using
   the single rotor rotamax intended for an aircraft application.
   Rotamax donated the engine to the school and also supplied two of
   the Hushpower II mufflers as a starting point.  The entire system
   was assembled on a test rig and run.  Unfortunately, we won't see
   any results until a new class takes over and continues the project.
   I've been in direct contact with Rotamax since the Findlay incident
   and they are waiting until they see the results of the NTSB report.
   I don't blame them for waiting before making comments.  This is the
   only Rotamax incident of this type I'm aware of.  On the other hand,
   the Sadler prototype probably had more hours on it than any of the
   other test vehicles.  Sadler hasn't made any public acknowledgement
   of the incident either.  They do have a backup position, having
   originally flown with the Rotamax 4-stroke.  You're quite right
   about the Aixro being charge cooled.  Perhaps the Mazda mill with
   lightened rotors is the way to go for testing.  To the best of my
   knowledge Phantom has dropped their X-40 development using the Aixro
   engine.  There was an Asian mini-helicopter company working on
   something similar and I haven't hear of any further developments
   from them either.

   best,

   George W

I think you mean Rotax 4-stroke. The final NTSB report could take years.
I doubt the NTSB will spend much money figuring out what happen as those types of non fatal crashes have super low priority.

One NTSB rotary powered Coot fatal crash report was totally erroneous. They took the engine to a Mazda dealer and he reported the reason the engine stopped was the apex seal oil metering pump was removed :) I and others tried to get the NTSB to correct the report and they stone walled us on it. Robin even knew the NTSB board member John Goglia and I contacted him directly. No response. The NTSB report in this case is pure fiction. Notice the apex seal oil metering pump has absolutely nothing whatsoever to do to do with the rotor or main bearings. If indeed the engine seized the pilot probably took off with no oil in the crankcase as as the flight was only 1 minuted or so. The report implies the missing metering pump was the cause of the engine seizer.  One guy flew his rotary powered airplane from Tennessee to NY without adding oil to the fuel tank. I am sure Ken Welter has some comments on this accident.

Paul Lamar

-------------------------------------------------------------------
SEA02LA072

HISTORY OF FLIGHT

On April 21, 2002, approximately 1305 Pacific daylight time, a Gallagher Taylor "Coot" experimental amateur-built airplane, N41RG, was destroyed by impact forces and a post-crash fire in a collision with terrain following a loss of engine power and subsequent loss of control near Creswell, Oregon. The private pilot-in-command, who was the airplane's sole occupant, was fatally injured in the crash. Visual meteorological conditions were reported at Mahlon Sweet Field, Eugene, Oregon, at 1254, and no flight plan had been filed for the 14 CFR 91 flight.

Witnesses at the airport who were observing the pilot's first flight in the accident aircraft reported that shortly after takeoff, the engine began to run rough and subsequently quit. The aircraft then nosed down and collided with the terrain in an open field about one mile west of the airport and caught fire. The flight duration prior to the accident was approximately 1 minute and 15 seconds.

PERSONNEL INFORMATION

At the time of the accident, the pilot held a private pilot certificate for single-engine land aircraft. The pilot's flight logbook was not made available for review, however, during the pilot's last Federal Aviation Administration medical examination, he reported a total flight time of 250 hours, with zero hours in the preceding six months.

The pilot was issued a third class medical certificate on June 14, 2000, with a restriction that he must wear corrective lenses.

AIRCRAFT INFORMATION

The accident pilot, who did not hold a mechanic or repairman/experimental aircraft builder certificate (according to the FAA airman registry), had bought the aircraft from a previous owner. The engine installed at the time the accident pilot bought the aircraft, an IO-360 series aircraft engine, was subsequently replaced with a Mazda 13B rotary automobile engine. An airworthiness inspector from the FAA's Portland, Oregon, Flight Standards District Office (FSDO) had approved the automotive engine installation.

According to the FAA aircraft registry, the aircraft was issued an experimental/amateur-built airworthiness certificate on June 7, 2001, and an airworthiness update was accomplished on September 24, 2001. An FAA inspector reported that the accident flight was the pilot's first flight in the accident aircraft.

Prior to the maiden flight, witnesses at the airport reported that the pilot had accomplished several high speed taxi tests. During one of these taxi runs, the aircraft was observed to have inadvertently lifted off the taxiway. The aircraft then landed hard and ran off the taxiway damaging one of the airplane's main landing gears. The pilot also reported that the airplane had been pulling to the right during these taxi tests.

The pilot's wife and several people at the airport reported that during conversations with the pilot, he had been trying different fuel/oil mixtures for the engine. Each time the pilot ran the engine, the spark plugs would get fouled.

METEOROLOGICAL INFORMATION

The 1254 Eugene, Oregon, airport hourly METAR weather observation reported conditions there as: wind from 350 degrees true at 9 knots; visibility 10 statute miles; overcast at 3,200 feet; temperature 13 degrees C; dew point 8 degrees C; and altimeter setting 30.19 inches Hg.

WRECKAGE AND IMPACT INFORMATION

The accident site was located in a level open field covered with short grass approximately one mile west of the Creswell Airport. The fuselage was completely consumed and destroyed by the post-crash fire. Both the left and right wings were laying flat on the ground and oriented in place to the fuselage. Fire had consumed the majority of both wings out to the tips.

The engine was positioned at the nose of the airplane. The nose of the engine was pointing straight up. The propeller remained attached to the crankshaft.

FAA inspectors who responded to the accident site and performed an on-site examination of the aircraft wreckage reported that they found no evidence of malfunctions in the aircraft's airframe or flight controls.

MEDICAL AND PATHOLOGICAL INFORMATION

The Chief Deputy Medical Examiner from the Lane County Health and Human Services Medical Examiner's Office reported that the pilot's cause of death was due to blunt force injuries in chest and abdomen.

Samples for toxicology were sent to the Federal Aviation Administration Civil Aeromedical Institute, Oklahoma City, Oklahoma, for analysis. The results of the analysis were negative.

ADDITIONAL DATA/INFORMATION

Following the FAA inspectors' on-site wreckage examination, the aircraft's engine was moved to the service facility of Kiefer's Eugene Mazda in Eugene, Oregon, where a disassembly examination of the engine was conducted by a Mazda service technician under the supervision of the FAA inspectors on April 23, 2002. The disassembly examination disclosed that the engine was seized, with both rotors, an oil pump, and the rotor bearing surfaces exhibiting galling and burn damage consistent with oil starvation. The inspectors reported that a metering oil pump, which supplies oil to the combustion chambers, was noted to be missing from the engine installation, with its drive absent. The Mazda service technician reported that further examination disclosed that the oil injection nozzles associated with the missing metering oil pump were also missing from the combustion chambers, and that the nozzle holes were plugged with a non-metallic substance.
--------------------------------------------------------------------------



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.