>> I have a small plumbing problem- I'm using 1
1/2" ID silicon hose for my
>> cooling, but I have one 45 degree bend where the
hose kinks. I'm
>> thinking of puting some sort of bent pipe or
tubing inside the bend to
>> keep it from kinking. I know that some cars have
anti-collapse springs
>> in the hoses. Does anyone know of anything that
will do the job in this
>> application?
>>
>> I'm really close to having this plane running
and doing some tests, this
>> is one of the little problems I have to figure
out. I don't want to
>> connect teh hose to a pipe bend, because that
will introduce two more
>> connections, and therefore two more potential
points of failure.
>>
>> Brian Trubee,
>> Rv-4, hope to finish by years end.
>>
>>
----------------------------------------------------------------
>>
>> If you have room Brian put a short section of bent
aluminum tube in there.
>> Also try this outfit for formed silicone hose.
>>
>> http://www.samcosport.com/usa/index.asp
>> It is made in the UK so it is probably REAl
expensive
>>
>> Here is another way of doing it. Carve a male mold
out of Styrofoam
>> and make your own hose. The foam can be removed
using acetone and the
>> plastic
>> wrap stripped out.
>>
>> If you had my book "How to Cool Your
Wankel" you would know about this :)
>>
>> Step 1: cut the form out of plastic pipe the right
size or Styrofoam.
>>
>> Step 2: wrap the pipe form with 10 or more layers
of thick (3 mil) clear
>> plastic. Hold in place with scotch tape.
>>
>> Step 3: wrap with one or more layers of Teflon
tape sticky side out. Part
>> number
>> 3M Permacel P421 3/4. There are other brands of
this tape that can be
>> used. They
>> come in different thicknesses and widths. McMaster
Carr calls it PTFE
>> Teflon
>> Tape. Very important to line your hose with Teflon
if it is going to be
>> used in
>> an intake manifold as silicone is affected by
gasoline.
>>
>> Step 4: wrap with one or more layers of red
silicone tape. Part number
>> Versaitek
>> Moxness 603 1 inch red sticky side out. There are
other brands of this
>> tape that
>> can be used. They come in different colors,
thicknesses and widths.
>> McMaster
>> Carr calls it Self-Fusing Silicone Rubber Tape. I
prefer the red as it is
>> more
>> likely to be compatible with red RTV.
>>
>> Step 5: Cut at least two layers of fiberglass
tape.
>>
>> Step 6: Wet out the layers of precut fiber glass
tape with red RTV between
>> layers of clear plastic. Strip off the plastic and
wrap the saturated
>> fiberglass
>> around the form.
>>
>> Step 7: Finish wrap one or more layers of red
silicone tape sticky side
>> down. It
>> takes longer to describe the process than actually
doing it. What you now
>> have
>> is high quality, fiberglass reinforced, Teflon
lined high temp hose. See
>> the
>> attached for the step illustrations.
>>
>>
>> Paul Lamar
>
>
> Paul,
> Have him check Pegasus.com , they have preformed
silicone hose with 90, 45,
> and 120 bends .
> Bill Schertz
> KIS Cruiser #4045
> N343BS
> I'm going to try bending a 1 1/4 " dia piece
of aluminum tubing to
> place inside the coolant hose to prevent a kink in the
bend that is
> causing me problems.
>
>
> Another question- is there a preference for types of
anti-freeze- the
> green or the reddish stuff?
>
> Brian Trubee
Automotive hoses sometimes have coil springs inside them -
presumably
to counteract collapsing.
Regards,
Matt-
I believe the green :(ethylene glycol) is superior to propylene glycol. When
Dave ? (memory laps) had to land on the freeway near Bishop, CA a couple of
years ago, we had a good discussion on coolants. As I recall the major problem
I found with propylene glycol is that its viscosity increases drastically at low
temperatures which can essentially block coolant in the radiator and stop or
restrict circulation.
Joel
Over the Hill Materials Engr.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.