Subject: Folded core for a Glass Goose
From: Rotary Engine
Date: 11/25/2008, 12:03 PM
To: AAA Put this in the To box


It is very simple. The first half of the cooling block does 3/4 of  the heat
transfer because the air temp increase as it passes through the  core. The
rate of heat transfer is directly proportinal to the temperature  difference
between air and metal. The last half does only 1/4 of the work.  Therefore
thinner cores are more efficient. All other thinks being equal they  have
half the cooling drag of a 2 inch core.

Jerry Hey can weld it up. You are going to research the internet and  find
out where you can buy radiator cores or car heater cores. I'll help  if I
can
get a chance. You might make friends with a local car cooling shop  owner
and
find out where he buys his cores.

Paul Lamar
----------------------------------------------------

Paul,

OK....1" cores will do better for me than 2" cores at my airspeed.  I'll
mock
up a design with 6 x 1" cores (two of which will be for oil cooling)

Got contact info for Jerry Hey?

As you suggested I have been doing some internet research. Are there  any
possibilities for this cooler:
http://store.summitracing.com/partdetail.asp?autofilter=1&part=BMM%2D70298&N
<http://store.summitracing.com/partdetail.asp?autofilter=1&part=BMM%2D70298&N >
=700+0&autoview=sku I can't tell much about the size of the core. It  says
4" thick but I assume that includes the fan. The intakes are smaller  that
desired but maybe suitable with a manifold delivery.

Thoughts on these questions:

Do you prefer silicone hoses over braided steel hoses AN hardware?

What do you mean, "We only use the lower half of the header tanks." I
assume
there is a 1" tank the completely covers the cores on the top and  bottom.

A fan on the e-shaft is interesting. What affect would spinning it  at 7,000
rpm be?

Thanks, Sandy

Jerry Hey <jerry@jerryhey.com <mailto:jerry@jerryhey.com>>

Yes on the silicone hoses. AN hose in that size is too costly, heavy  and
stiff.
The stiff and heavy part tend to crack what ever it is attached to.

In a car radiator plastic is used for the header tank and it is  fastened to
the core with bent over aluminum tabs. These are unbent using a pair  of
pliers and what is left is the bottom of the header tank aluminum  brazed to
the tubes in the core. You weld that part to the new larger header  bottom
plate with large slots in it. Then you weld on the new top plate.

That Summit racing core is not the right kind for the water part.  Two of
those would be OK for the oil cooler part. This would be a better one.
http://store.summitracing.com/partdetail.asp?autofilter=1&part=BMM%2D70272&N
<http://store.summitracing.com/partdetail.asp?autofilter=1&part=BMM%2D70272&N >
=700+115&autoview=sku

A radiator repair shop is a good place to start for the water cores.  They
are supplied by a whole sale radiator core supplier. These are the
companies
you are looking for. Sometimes you have to set up a phony company to  do biz
with them because you are buying several and you need a discount. If  you
can
find somebody else building a Goose that would help to increase the  volume
and reduce the price.

U S Auto Radiator Supply Co
4358 N Dixie Hwy
Fort Lauderdale, FL , 33334-3832
Phone: 954-561-2665
FAX: 954-651-5946

Jerry Hey might be talked into doing that as he already has a biz.  He can
tell them he builds custom rads. Jerry lives near Fort Wayne Indiana.

ASAP Radiator & Supply
1936 N Loop Ave
Casper, WY , 82601-9227
Phone: 307-266-5606
FAX: 307-266-5604
Toll Free Phone: 800-675-5606
Business Activity: Manufacturer

For more put in "wholesale radiator supply" in google.

A fan on the e-shaft will be limited in diameter and blade width so  7000
RPM
should be no problem for a eight or ten inch diameter fan.
Best made from carbon fiber as the tensile strength to weight ratio  is very
good. If you make the blades flexible they will lose pitch and  reduce HP
consumption at high RPM like this fan I used on my mid engine  Firebird. Or
get one of these Summit electric fans and cut the ends of the blades  off to
8 or 10 inches in diameter and throw away the electric motor
:)

Paul Lamar
----------------------------------------------------------------------------
-------

Paul,

I've been doing my radiator homework you assigned me. I've contacted  over
thirty different radiator companies....radiators for tractors, ATVs,
motorcycles, fork lifts, etc. Small radiators are really tough to  find OTC.

Here's a potential OTC water radiator ($50) for the cooling block.  It's 10"
x 8.5" x 1.5"
http://www.atvpartsusa.com/itemdetail.asp?partno=500093

It has a fan ($20) available for it:
http://www.atvpartsusa.com/itemdetail.asp?partno=500102

What do you think about the potential for this radiator in a cooling  core?

Could I make a manifold to flow water correctly to four of these  radiators?

Sandy McNabb

Looks promising. It is from a Tank Touring 250 motor scooter.
Chinese copy of a Honda 250 Scooter no doubt. A bit on the small  side but
might work OK given five of them. Cheap enough.
Engine Type 250cc 4 Stroke
Displacement 244.3 ml
Max Horsepower 16.1HP/8500 rpm

This could be a fertile hunting ground for the right core.
Perhaps a 500 cc motor scooter core would be better.
A trip to your local ATV/Motor-Cycle/Scooter store might be in order.

I would cut the top and bottom tanks off and weld them to common  tanks.

Paul Lamar
----------------------------------------------------------------------------
-------------------------
Paul,

I'm still looking for radiators.

I really, really like the size and shape of these coolers:
http://www.autoanything.com/coolers/65A3049A0A0.aspx? kc=0&from_search=1
<http://www.autoanything.com/coolers/65A3049A0A0.aspx?kc=0&from_search=1 >

However, they're oil coolers with 1/2" NPT. Would it work to weld on  11/2"
hose connections to replace the 1/2" NPT?

Would the 1/2" NPT work with a manifold connecting a bank of four of  these
radiators in a cooling block?

Jerry Hey isn't answering his email. Gotta phone number for him?

Thanks, Sandy

Sandy, let me work on this when I get back on Tuesday.

Paul Lamar Still in Oxford UK

---------------------------------------------------------------------------

Isn't the thermostat hole the limitation to the whole cooling system?

Sandy

Not on an RX8 motor. The thermostat housing comes off.

Paul Lamar

----------------------------------------------------------------------------
-

Paul,

OK....case closed on oil coolers for cooling water. I just talked  with an
engineer at Fluridine. They make water radiators and oil coolers.  Why won't
oil coolers work to cool water??? The interior tubes in an oil  cooler are
much larger than the water radiator tubes due to the viscosity of  the oil.
An oil cooler won't do a good job on water cooling due to laminar flow
inside the interior tubes. I guess that's a "duh" on my part.

Sandy

OK are we good to go with small cores in a folded core configuration?
Do we need any more research on small water core suppliers.

Paul Lamar

Sandy,
Have you looked at the radiators on the new 4 cycle single cylinder  dirt
bikes? They have compact radiators of about the correct width. They  are
probably more expensive than you would have wanted but they are tough.
All aluminum braized core and tank. Paul would Ed Kleppis be able to
make up the radiators? Sorry I know I spelled the name wrong, but he
claimed that he could get the core used on the Mazda racing oil cooler
which was great stuff. Water radiators would be much easier I would  think.
Bill Jepson


I don't know about Ed but Jerry Hey can weld them up. Actually any  good
TIG welder could weld them. Even I could do it if I practiced for a  week
before hand :) TIG welding aluminum is joint specific. One kind of  joint is easier than another. The hardest kinds are butt welds.

Paul Lamar

I would be happy to look at it but I think Ed Kleppis could do it
without having to go through the learning curve.  Try Ed first is my
recommendation.    Jerry

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.