Isn't the thermostat hole the limitation to the whole cooling system?
Sandy
Not on an RX8 motor. The thermostat housing comes off.
Paul Lamar
----------------------------------------------------------------------------
-
Paul,
OK....case closed on oil coolers for cooling water. I just talked
with an
engineer at Fluidyne. They make water radiators and oil coolers.
Why won't
oil coolers work to cool water??? The interior tubes in an oil
cooler are
much larger than the water radiator tubes due to the viscosity of
the oil.
An oil cooler won't do a good job on water cooling due to laminar flow
inside the interior tubes. I guess that's a "duh" on my part.
Sandy
OK are we good to go with small cores in a folded core configuration?
Do we need any more research on small water core suppliers.
Paul Lamar
Sandy,
Have you looked at the radiators on the new 4 cycle single cylinder
dirt
bikes? They have compact radiators of about the correct width. They
are
probably more expensive than you would have wanted but they are tough.
All aluminum braized core and tank. Paul would Ed Kleppis be able to
make up the radiators? Sorry I know I spelled the name wrong, but he
claimed that he could get the core used on the Mazda racing oil cooler
which was great stuff. Water radiators would be much easier I would
think.
Bill Jepson
I don't know about Ed but Jerry Hey can weld them up. Actually any
good
TIG welder could weld them. Even I could do it if I practiced for a
week
before hand :) TIG welding aluminum is joint specific. One kind of
joint is easier than another. The hardest kinds are butt welds.
Paul Lamar
I would be happy to look at it but I think Ed Kleppis could do it
without having to go through the learning curve. Try Ed first is my
recommendation. Jerry
----------------------------------------------------------------------------
Paul,
To answer your question: "OK are we good to go with small cores in a folded
core configuration?" Absolutely!
I'm following up on a lead to contact Neil at Fluidyne Powersports. Those
guys specialize in radiators for ATV and motorcycles. Here's my email to
them:
I'm trying to cool a Mazda Renesis rotary engine and I have very limited
space to do it with. I'm looking for four small aluminum water radiators
with a cores about 11" x 9" (+- 1") by 1" or 1.5" thick. Can you help me?
Here's their response back to me:
---------------------------------------------------------------------------
Hello Sandy.thanks for your inquiry. I think we can help you. We can do an
11" x 9" x 1.5" core from standard parts. The tank depths are usually 1.5"
or so which will give you an overall height or width of 14". My suggestion
is to send a sketch of your desired dimensions, including inlet, outlet
tubes, filler neck etc. and we can respond with our best configuration for
your needs. If we can meet your dimensional requirements, the time to build
the parts is about two weeks. I will need a little more detail on the
fittings, brackets etc. prior to estimating the price. In any case, we'll
make it a fair deal.
I'll send them a picture of the cooling block and see what they think about
it. In the meanwhile, looks like they can fabricate a radiator in a size I
can use. Can you give me some specifics on some of their questions if I go
with four single radiators?
Dimensions:
Inlet: I think you said 1-3/8"
Outlet: I think you said 1-1/2"
Filler neck:
Any other requirements:
In the meanwhile I'll approach Ed Kleppis again. He was very helpful, but
suggested alternatives to the cooling block because of the difficulties of
welding it. I'll let you know.
Thanks, Sandy
The requirements look great.
You can send my 3D's to Fluidyne but give me credit
for the design. Give them my email address so if they have questions they can
contact me.
That is the trouble with Ed. He does not like to build it to the dwg.
I had him build a cross counter flow rad one time. When it was done he had
completely defeated the design by welding the cores together.
Fluidyne on the other hand would probably understand what you are
trying to do as they are engineers. I would not be a bit surprised if
they started offering it as an off the shelf configuration :)
What would really be cool (pardon the pun) is to have them mount
the water tubes at an angle. Not just the cores. That would reduce the drag.
Get them to quote it both ways. Give them an overall width and depth so they can
get the angles right. Can you live with 14 inches high? If not a one
inch high tank on both top and bottom would work. That would bring the
height down to 13 inches overall.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.