Paul,
Why doesn't this newsletter join the 21st century and go metric? It
seems difficult, but I have found it easy and convenient. It won't
cost a pound of flesh, as we inch forward, walking a mile in
standardized shoes.
Doug in Japan
Well here in the U.S. where most of our subscribers live we still
use inches and pounds of weight. BTW I was on a UK highway recently
and the Britts still use yards on the road signs.
BTW A Pascal is a ridicules unit as it says nothing about what it is.
psi on the other hand says everything about what it is.
Could you replace it by Kg/m^2, g/cm^2, milligram/micrometer^2, etc.,
etc., etc....?
You see where I am going with this :)
Paul Lamar
I have to agree with Randolph on this one. It is a complete disgrace to
America that we still do not use the metric system. Everyone else
adopted English as the international language, not because it is somehow
better, but for prevalence and economic reasons. Yet still, we cannot
seem to manage the metric system despite the fact that it is clearly
superior.
--
David Leonard
Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net
Easy for you to say Dave. You went through college on the metric system.
Us real old U.S. engineers still think in inches.... one inch at a time :)
I also think great progress was made in aviation in the 1930's and 1940's
in the U.S. and Briten. All that NACA engineering info is still relevant.
(German advances were kept secret.) All in the English system of units.
It is hard to ignore all that. Most of the great books on aerodynamics and
structures were written in english units. A lot of these books were
written by ex pat German engineers in the 40's, 50's and 60's like
Hoerner, Kuchemann & Weber, Von Doenoff and Bruhn. To rewrite these
books in the metric system would be a monumental effort. Then there are
the Taylor series of books on engine design. Still a major reference.
This is not going to happen in my life time and probably not in the
life time of most of the people on here.
What saddens me however is the wide spread lack of understanding of
physics in the U.S.. I don't know why this is so. Perhaps
physics and engineering are too hard for students brought up on inches
and thrust into the metric system in high school and college.
BTW here is another example of the nonsensical naming of units in
the metric system. Hertz verses cycles per second. CPS is self
explanatory like psi. If one can have meters per second why not
cycles per second? I'll give you another example: liters per 100
kilometers verses MPG. MPG is an instantaneous thing that changes
according to speed. You may say "I am getting x number of liters
per 100 kilometers"? How do you know until you drive 100 kilometers?
What speed are you driving? It might take all day to know. Maybe the
French system needs to clean up its act :) We could also do without
furlongs per fortnight :)
Also BTW I think a huge boost for English was the personal computer not
to mention it is the required language of international aviation.
Paul Lamar
--
Paul
Poo on the old dogs can't learn new tricks excuse. I came to Japan
having design things in inches and it took about one week to get
comfortable designing things in milimeters. If you are smart enough to
calculate the lift on a wing you are smart enough to calculate in metric.
I heard that USA was suppose to change to the metric system in 1975.
Consumers out-cry had an effect on it. For instance $1.00 a kilo seems
more expense than 45 cents a pound.
Doug in Japan
The best thing about the metric system is the units of linear measure.
Unfortunately they threw out the good stuff like psi and cycles per second.
What would you rather have in your house a thermostat that kept the
temperature to plus or minus one degree F or plus or minus 1 degree C?
Lets take nuts and bolts for exanple. There are three common thread measurements
in metric and only two in U.S. If you have a metric threaded hole in a part and
you need a screw to fit you are now in serious trouble. It is going to take you
twice as long to solve the problem. As far as I know in metric there is no
comparable system of fasteners to the AN system.
We could go on an on about this forever so we will stop this thread and use a
wonderful free online system to convert :)
http://www.onlineconversion.com/
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.