Paul,
I slapped my forehead when I figured this out.....DUH!
Considering the present cowling shape, I studied a variation of your
folded core cooling block. How about one fold....actually, two radiator
cores with a common tank between them in a vee shape.....intake port at
the top and exit port at the bottom. Scott Gettings keeps going back to
this plan, but the problem was fitting the vertical radiators in a
gradually sloping cowling. Then it hits me...why not give the vee
shaped radiators a 90 degree flip. Now, we've got a ton of room for
cooling core because it lends itself to the cowling shape (see One fold
horizontal radiator (Large).jpg). We have enough room now put more
cooling core for water AND oil than we need. With the rads mounted
vertically. it adapts well to wedge diffusers in a traditional shaped
horizontal intake.
I've also included some views of the cowling. Note that there is a lot
of exit air room down both sides of the engine (see Cowling rear
(Large).jpg)
In the attached file (One fold horizontal radiator - Thicker Core
Numbers (Large).jpg), there are some numbers for 1.75" and 2" cores.
Q1. What do you think about this plan? What adjustments would you like
to see?
Q2. The 1.5" core offers about what the RX8 has in cooling. Would that
be enough? I sure don't want to overheat in the summer on a Texas
taxiway. If there is any doubt I'd rather have the cooling drag than the
heat.
Q3. Can the top intake port and the bottom exit port be on the same
side of a radiator, or is it best to have them on opposite sides?
Thanks for you thoughts
Sandy McNabb
Renesis in a Glass Goose
Looks like it will work fine if you put the tanks on the sides instead
of on the ends. That way top and bottom rad will be in parallel instead
of series.
I talked to the president of Fluiddyne and he was not interested.
I think he was feeling the down turn, He wanted a minimum of 12 cores
12 by 12 by 1 at $300 each. They are worth $100 each at the most.
In other words $3600. He was not familiar with thermo principles.
The engineer if any was not there.
I found a company in Brisbane Aus that understood what we were trying
to do and agreed to make us anything we want including mounting the
tubes at an angle so they are aligned with the air flow. The exchange
rate is good with Aus and George Lendridge lives in Brisbane.
The company is PWR 103 Lahrs Road Orrneau Queensland 4208 The guys name
is Matt Bryson 61 7 55547 16111 Email is matthew@pwr.com.au
More on this when I get home.
Paul Lamar
Sandy,
Have you considered a double pass U- style radiator unit? This is really an
efficient use of the delta Ts. in air and water mediums. Mount this unit
where you show the lower V is. Air is ducted straight back (from the right
to left in your picture) and the another exhaust duct delivers it up and out
the top through a cowl flap. This is exactly what I am doing with my
SeaWind set-up but of course yours is a tractor mount. I need a long duct
but you have the advantage of going forward with the cowling and making a
nice inlet shape.
I am concerned you may want all of that area just for the water heat
exchanger. I am also concerned that you are pouring warm air over the
engine, through a fan blade, and other obstruction so that you will limit
the air flow and vastly increase cooling drag. No obstruction on the inlet
and exit is the mantra I have been hearing for about 5 years
now:) And the oil coolers? Put a long 20 B style "2D x 4.5W X23"L along
side the port side bottom quadrant (about 5 o'clock and bring the air in
through an side ear scoop where the cowl is widest. Duct the exhaust out
near the PSRU and the put the prop to work helping to pull air through the
oil cooler as well allowing you to minimize the inlet size. Adjust the
inlet ear in and out to regulate oil temperatures.
Doug in Japan
Doug,
Thanks for getting into the fray.
U-style radiator? Have you got a drawing or a picture of the design? Is
there anybody that can fabricate it?
The Glass Goose is a pusher, not a tractor (see Glass Goose (Large).jpg
attached).
The reasons for putting both the water rad and the oil cooler up front are:
1. There is ample room for both (see One fold horizontal radiator with 2
inch cores (Large).JPG attached). 2. Simple plumbing. 3. Unimpeded access to
airflow. 4. A better location than any other for CG (I need weight
forward).
The fan is just a thought for an option. I don't think I'll need it. I
suspect the prop with do a more powerful job of pulling air through the
system. I agree, I'd rather not exhaust air over the engine, however, there
is plenty of room on both sides of the engine for exhaust (see IMG 7383
(large).JPG and IMG 7382 (large).JPG attached). In fact, I'll probably
modify the stock cowling (for a Lycoming) to narrow it's profile. Still it
would be best to have unimpeded exhaust air if possible. Seems like
everything is a compromise. While the air coming out of the radiator is hot,
I "think" it is a breath of fresh air to the hotter engine, although outside
air would certainly be better....more compromises. Hot radiator exhaust air
doesn't add to the engine's heat, but relieves it somewhat.....I
"think"....but I could be wrong.
I like the idea of reducing intake area. I don't like how big my intake is
(32.5% of radiator face). It's 8" x 20" for both water and oil. However, I
keep coming back to the requirements for intake area regardless of where the
intakes are located on the cowling. The intake areas are the same no matter
how the areas are divided up.
Thanks,
Sandy in Texas
Renesis in a Glass Goose
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.