Subject: Engine mount photos (RV-4) Weights
From: Rotary Engine
Date: 1/14/2009, 11:01 AM
To: AAA Put this in the To box


>> Paul,  here are photos of the RV-4 engine mount which I finally got
>> welded up after some delay.  I will post about 25 photos on my web site
>> later this week.  If you would like to have them I will send to you as
>> well.  The main difference is the improvement in weld appearance which I
>> am extremely pleased with.  Total weight with the Barry bushings, oil
>> pan and  pick up tube is 26 lbs.  This mount does gain some weight
>> because of the landing gear sockets and associated structure.  I like
>> the first photo which shows how the rear beam is used to tie everything
>> together while at the same time keeping the tubing well clear of the
>> engine.     Jerry
>>
>>
>> That is a beauty Jerry. Yes send them to me.
>>
>> Paul Lamar
>
>
>
> Great job Jerry.  Regarding comparative weights, a stock RV-4 Lycoming mount
> is exactly 15 lbs including gear leg sockets and dynofocal mount seats but
> no rubber mounts/bushings, but it appears an accurate weight comparison
> would provide for subtracting from your rotary engine mount the total weight
> of the oil pan and pickup, and Barry bushings.   Do you know the total
> weight of those components?  Paul, are the mount dimensions for the cowling
> shape you showed in your note yesterday?
>
>
> Steve Beckham.

> Jerry is a bit conservative on the oil pan wall thickness
> at .125. Easier to weld than .090" thick. My guess for the oil
> pan is 3 to 4 pounds. If it is .1875 thick it would be 4 to 5 pounds.
> One difference is the 4130 .0625" thick Schertz beam as it is long enough
> to accommodate a muffler or turbo charger mounted adjacent to the engine.
> It also keeps the rubber bushings away from the exhaust heat as far as possible.
> It weighs about .21 pounds per inch less the lightening holes. If it were 20" long
> it alone would weigh about 4 pounds less the mounting bolt tubes. My guess is
> 5 pounds. I would not go down on the thickness to .049" to save weight.
>
> Here are the RV4 mount dimensions.
>
> Any idea what a Lycoming O-360 oil pan weighs?
> Total weight of the O-360 is about 290 pounds.
> The rotary with 40 pound PSRU less rads and coolant is
> about 260 pounds to 270.
>
> If you used Racing Beat aluminum end housings you would have
> an aft CG problem :)
>
> Paul Lamar

The s-beam motor mount usually has a larger diameter  (1")
lower tube (from lower firewall corner to S beam) to deal
with compressive forces in a hard landing.  Paul can speak
much better than I about the engineering.  I can say that
strength and safety were paid proper attention.

Steve,  here are component weights.  Note that the length of the S-
beam can vary from 31 inches down to 24 inches depending.  A few oz
could be saved using thinner aluminum in the pan but, as Paul has
said, I am not comfortable with it.  Paul has considered at my
request  making the S-beam out of .049 4130  or  .250" aluminum but
has rejected these after running the numbers and fatigue
characteristics.

component weights:

S-beam: 4 lb  11.3 oz.

2 Barry Mounts with .5" bolts  1 lb  4.6 oz

oil pick up"  5.1 oz

rear Barry Mount 4.6 oz

Aluminum oil pan ( 6.5 qt) 4 lbs  8 oz

By Comparison:
Renesis steel oil pan (3qt): 4 lb 5 oz.

Photo attached

Jerry

-
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.