Subject: New super cheap super simple fuel injection article.
From: Rotary Engine
Date: 1/16/2009, 4:13 PM
To: AAA Put this in the To box


    Not entirely done as I will be updating it from time to time
    depending on your questions.
    http://www.rotaryeng.net/simple-cheap-555.html


    Paul Lamar

    Paul,

    Thank You!!!!!

    Joe

    Your welcome Joe.

    Paul
    Lamar



    Paul,
    nice write up. The only thing we are doing signifigantly differnet is to
    sum
    in 2 thermocouples for engine temperature and for inlet air temp in the
    control portion. Then engine will want to be a little rich for cold start
    and idle stability until temps are up a little.
    Just makes it more user friendly.
    Larry


    Thanks Larry.
    Yes it would be. As it is now it is about as user friendly as my C182 :)
    Full rich for takeoff, climb out and landing. The carb has no temperature
    compensation :) I am used to it.

    Paul Lamar


    Paul,
    the 182 is also running considerably richer than a liquid cooled engine at
    full rich as they use the fuel to cool the cylinder heads. We only need to
    be rich when the engine temp is low. By the time you taxi to the active
    and
    do a run up, there should be enough temp to not need a rich mixture. Full
    power rich on the
    rotary is considerably leaner than the air cooled
    engines,
    but our cold start mixture is about the same. I just prefer to automate a
    known and predictable condition.
    During taxi, I am busy doing the CIGARS checklist and prefer the engine
    takes care of itself.
    Spark plug life will be much better if we correct the air fuel based on
    temperature. Rich mixtures on a rotary is hard on the plugs.
    Larry

    Well all that may be true but SOP in most air cooled light aircraft I am
    familiar
    with and have flown (Cessna's, Pipers and Mooney's) is to take off and
    climb out at
    full rich. In the case of aircraft turbo engines the BSFC is a high 0.65.
    That has got to be around 10:1 air fuel mixture or worse. Max power is
    12:1 and best cruise is 14:1 or higher. The exception of course is high
    altitude airports where you set the mixture to max static RPM and power.

    I am not saying temperature comp. is
    a bad idea. It just makes it a lot
    more costly, complicated, harder to build, trouble shoot and repair. I want to
    keep this as simple as possible to keep it as cheap, reliable  and easy to
    build for the home builder.

    There is a subsidiary advantage to pilot involved simple carburetors and
    fuel injection. It trains the pilot as to what is really going on with the
    engine.
    If things are too automated the pilot has less awareness of how the
    mechanism works.

    I once had a float sink in a C172 carburetor. I was able to identify the
    problem and keep
    the engine running by judicious leaning until I was able to land. Without
    leaning the engine would flood and quit. My knowledge of carburetors was
    invaluable at that point.

    Paul Lamar


   Paul
   Those stinking sinking floats.....
   I looked up the fuel multiplier code for cold start and it increases pulse
   width by 20%  with the engine
    cold and then continues to decrease this
   percentage as the engine water temp comes up until the multiplier is at 0%
   at around 160 deg.
   It also uses a time since start multiplier to also decrease this value but
   for what we are doing, we will ignore this.
   We are breadboarding up a control board with 2 thermocouples built in. Looks
   like it will be very easy to go either way. if you don't want the temp
   compensation.... leave them out and their values won't get summed in the
   control.
   I'll pass on the results next week some time.
   Larry


Would you want to consider thermistors instead of thermocouples?  They
are less expensive and have a signal in the volt range instead of
millivolts.

Philip Groelz


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.