Subject: New super cheap super simple fuel injection article.
From: Rotary Engine
Date: 1/16/2009, 7:38 PM
To: AAA Put this in the To box


  Not entirely done as I will be updating it from time to time
  depending on your questions.
  http://www.rotaryeng.net/simple-cheap-555.html


  Paul Lamar

  Paul,

  Thank You!!!!!

  Joe

  Your welcome Joe.

  Paul Lamar



  Paul,
  nice write up. The only thing we are doing signifigantly differnet is
  to
  sum
  in 2 thermocouples for engine temperature and for inlet air temp in the
  control portion. Then engine will want to be a little rich for cold
 start
  and idle stability until temps are up a little.
  Just makes it more user friendly.
  Larry


  Thanks Larry.
  Yes it would be. As it is now it is about as user friendly as my C182
  :)
  Full rich for takeoff, climb out and landing. The carb has no
 temperature
  compensation :) I am used to it.

  Paul Lamar


 Paul,
 the 182 is also running considerably richer than a liquid cooled engine
 at
 full rich as they use the fuel to cool the cylinder heads. We only need
 to
 be rich when the engine temp is low. By the time you taxi to the active
 and
 do a run up, there should be enough temp to not need a rich mixture. Full
 power rich on the rotary is considerably leaner than the air cooled
 engines,
 but our cold start mixture is about the same. I just prefer to automate a
 known and predictable condition.
 During taxi, I am busy doing the CIGARS checklist and prefer the engine
 takes care of itself.
 Spark plug life will be much better if we correct the air fuel based on
 temperature. Rich mixtures on a rotary is hard on the plugs.
 Larry

 Well all that may be true but SOP in most air cooled light aircraft I am
 familiar
 with and have flown (Cessna's, Pipers and Mooney's) is to take off and
 climb out at
 full rich. In the case of aircraft turbo engines the BSFC is a high 0.65.
 That has got to be around 10:1 air fuel mixture or worse. Max power is
 12:1
 and best cruise is 14:1 or higher. The exception of course is high
 altitude
 airports where you set the mixture to max static RPM and power.

 I am not saying temperature comp. is a bad idea. It just makes it a lot
 more
 costly, complicated, harder to build, trouble shoot and repair. I want to
 keep
 this as simple as possible to keep it as cheap, reliable  and easy to
 build for
 the home builder.

 There is a subsidiary advantage to pilot involved simple carburetors and
 fuel injection. It trains the pilot as to what is really going on with
 the
 engine.
 If things are too automated the pilot has less awareness of how the
 mechanism
 works.

 I once had a float sink in a C172 carburetor. I was able to identify the
 problem and keep
 the engine running by judicious leaning until I was able to land. Without
 leaning
 the engine would flood and quit. My knowledge of carburetors was
 invaluable at
 that point.

 Paul Lamar


 Paul,

 Did some research on air flow sensors.  It seems that there are few after
 market models that go up to $300.00 range.  It would be nice to refurbish
 one from a junk yard.  Even the OEM replacement at the auto parts stores
 are
 over $100.00.  Just trying to keep it cheap. but safe.

 Joe

Paul,
we are basing ours on the 70mm 1996 and up mustang part. it has a built in
air temp sensor and will handle airflow up through a 20B.
They came in plastic body and aluminum. I prefer the plastic part due to
lower weight.
I will get you the correct Ford part numbers that will have the same
calibration.
Larry

Not to mention lower cost.
When you get an engine going I'll pop up there and take some pictures.

Paul Lamar

Paul,
I plan to have the engine on a test stand by the end of February. Should time
well with your return from south.
Larry

Great Larry. That will be fun to play with.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.