I am going to be doing some injector flow testing
in my office at home where I have a lot of test
equipment.
Anybody know of a fluid with about the same viscosity
as gasoline that is non explosive?
Paul Lamar
Hi Paul,
Must be getting old...you're getting conservative: )
You could run a control test on one injector with gasoline.
Then use the
same test parameters with rubbing alcohol and ratio the
results.
Additional injector tests would be done with the alcohol
and apply the
ratio to get the gasoline equivalent.Dave M
In order to attain the status of Old and Conservative, one must survive
the period of Young and Dumb.I sometimes wonder how I did it.
As to the choice of substitute liquids to substitute for gasoline
which has a viscosityof 0.4 cP to 0.5 cP at room temperature
the following come to mind.
Water 1 cP
Stoddard solvent (Paint Thinner)1 cP
Carbon Tetrachloride0.5 cP
Joel
Thanks Joel.
I think carbon tet might affect the plastic in the fuel pump
and injectors. I think I'll just set up outside of the hangar.
The weather is not that bad out here. Too lean to ignite.
Paul Lamar
Paul,
just put a length of clear tygon hose over the output end of the injector
and then the hose into a graduated container. The fuel will condenseon
the
walls of the tube and help eliminate the potential hazard. Just as anote,
I
was at a fuel injector rebuild shop having injectors matched, and
theyeven
used gas in their test equipment, so a direct equivalent must be hard to
find.
Larry
Sounds like that will work. Thanks for the tips.
Paul Lamar
Hi Paul;
I have setup something similar to do backyard fuel injector cleaning and
calibration.
I have used several (graduated) metal capped mason/bell glass jars.I
drilled a hole in the cap to insert the spray nozzle of an injector and
held it in place with a jig / duct tape.The jars were not perfectly
sealed - you could vent them elsewhere.
Connect the FI with a few worm clamps and clear tubing to a fuel source.
(or just several feet of hose filled with fuel).
I used a large volume tank compressor connected to the fuel source (or
fuel filled clear tubing) to provide the desired pressure. (say 40 psi)
You can pulse the fuel injectors using a spare FI connector pigtail.A
9V battery will drive them for a while.A batter charger is a better
choice.
If the injectors are not new and have been sitting for while, they are
likely gummed up - you might want to:
- check they are not stuck, (for really stuck FIs you may need to
reverse flow them under pressure)
- check they are not leaking,
- run some cleaner through them,
- check the spray pattern, and
- reverse flow them under pressure to clean the fine filter screens.
A few extra hands, duct tape or a jig go a long way.
Keep a fire extinguisher handy just in case.It is not nearly as bad as
your P-port dyno fuel spray video ;)
Sorry, no pictures.
Cheers
Cary
Thanks Cary. I am mainly interested in the minimum flow down
around 1 ms. I'll use the 555 injector system I have built up
to check it at 720 RPM although we rarely idle the engine
below 1800 RPM due to gear box chatter. (prop RPM 650).
I have a ball park idle fuel flow figure from a tech paper
on the side exhaust RX8 engine. At 720 idle RPM the RX8 engine burns
about 1 liter per hour full lean. About .3 L/hr less than a
p-port exhaust 13B engine. I have a p-port intake with a side
exhaust so that should match the stock RX8 engine for fuel
burn at idle.
So that means I should be able to get the flow down to 1/4 liter per
hour per injector and about 20 liters per hour per injector full
power. In other words the dynamic range is 1/4
L/hr to 20/L/hr at full 80% pulse width, full power at 7500 RPM.
If you figure roughly four liters per gallon.
That would work out to about 5 gal/hr per injector or 31 pounds of fuel
per hour per injector full power 7500 RPM. Total fuel weight for four
would
be 125 pounds per hour. At a BSFC of .5 that is about 250 HP. Might
have to richen it up a bit on the top end as Larry suggested. I can up
the fuel pressure to do that.
I want to check the dynamic range so I can be sure four RX8 yellow
injectors
will work from 1800 RPM idle to 7500 full power 250 HP without staging
on the P-port RX8 engine shown in the youtube video. I really don't think
staging is necessary.
http://www.youtube.com/watch?v=LkKw72dZ2yc
BTW We have had 18,000 hits on that Youtube "How to weld a p-port RX8
motor"
and nobody has said it won't work yet :) Obviously somebody somewhere,
out of that 18,000, has built one besides me in the last year since it
has been up there. I saw a figure in an Aussie mag that 200,000 RX8s have
been sold so far world wide.
Richard Sohn.... check out the video. There really is
a welded p-port RX8 engine running :)
If I feed the manifold pressure into the 2 port fuel pressure regulator
the fuel pressure should go up as the power increase from idle expanding
the dynamic range.
Paul Lamar
Paul,
Saturation sytle injectors takes around 2ms to react before opening. this is
one of the calibration points we use in tuning. the injector closes much
faster than it opens, so when you test, start at 1ms pulse and slowly
increase the pulse length until you get the injector to fire. if you want a
1 ms open time, add 1ms to the time delay to open and you will end up around
a 3ms pulse to get a 1ms open time.
This really doesn't effect us, but if you need faster response time, you
have to go to a peek and hold injector as they are around .7 to 1 ms
response time.
Larry
The new skinny saturations appear to work faster. Down to about 1 ms.
Important if you are using high pressure to squirt a lot of fuel
on the top end. At 7500 RPM in a rotary you don't have a lot
of time on the top end as it fires once per rev while a 4 cycle
piston cylinder fire once every other rev.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.