Subject: Connectors for Mazda fuel injectors and pump wanted. 555
From: Rotary Engine
Date: 3/1/2009, 9:37 AM
To: AAA Put this in the To box


  Anybody know where I can get some connectors
  for Mazda fuel injectors and high pressure fuel pump?

  Well I have the test fuel plumbing done.
  I don't recommend that Airmotive fuel pressure
  regulator because it leaks vacuum around the adjusting screw.
  I think a TWM might be a better brand.
  When the manifold absolute pressure goes down, because the throttle
  is partially closed, so too the fuel pressure. The bottom line is:
  it widens the dynamic range of the injectors without staging.

  Paul Lamar


 Paul,
 connectors:
 http://www.injector.com/electricalcomponents.php?PHPSESSID=7fd862561f2b8aab206624c8c5b21a28

 Also note, all the adjustable pressure regulators leak a little bit at
 the
 threads. when an engine is supplying the vac sourse, the leak is so
 small it
 doesn't make any difference.
 if you are using a hand vac pump, you can rubber band a balloon (i
 won't say
 what kind!) over the diaphram cap to stop the leak for your testing.
 Larry

 Good idea Larry! Thats funny :)
 My Aeromotive FPR leaks down from 15 inches of Hg to 30
 inches of Hg in 3 seconds.

 I found some connectors to use in a pinch.
 These are Molex female connectors for use with PC power
 supplies. They are on the ends of the wires coming
 out of the power supply and the male pins are on the
 mother board. They just fit on the  injector rectangular male pins
 despite being round. A buck for a whole bunch at Fry's. You can
 also salvage them from a obsolete PC power supply. After you stick them
 on there and you want to fly with them squeeze a little red RTV
 around them and that will stabilize them and keep them in place.

 BTW Klause tells me he uses paint thinner for oil based
 paint instead of gasoline for testing injectors. According
 to him it is much less flammable. It is handy having his 555 experience
 available. He said he is going to buy the systems from me when
 I get them done but I think he was joking :)

 Paul Lamar

Hi Paul;

Are you looking for electrical or fuel fittings for the rx8 fuel pump?
Is it a walbro?
www.apeusa.com and lots of other places carry a variety.
www.summitracing.com  good for most things non-walbro


Here is an old list of Fuel Injector info from rx7club.com.  Plus
additions.  Not sure about the RX8 injectors.

(Note that some injectors carry the same part number as others but plug
styles and resistances can vary.
Low impedance refers to 2-3? ohms, high impedance refers to 12-13? ohms.)

Year   type   impedance plugStyle plugNotchPosition  flowRating color
partNumber

84-85  13B NT low       square    center             680cc      orange
195500-0900
86-87  13B NT low       square    center             460cc      red
195500-1350
86-87  13B T  low       square    center             550cc      tan
195500-1370
88     13B NT high      square    offset             460cc      purple
195500-1350
88     13B T  high      square    offset             550cc      purple
195500-1370
89-91  13B NT high      oval      center             460cc      red
195500-2010
89-91  13B T  high      oval      center             550cc      purple
195500-2020

MSD-2400 will fit the square center connectors -
http://store.summitracing.com/partdetail.asp?part=MSD%2D2400

Attached is a (poor) pic of a connector from:
http://www.fiveomotorsport.com/Injector_CONNECT.asp - see *NipponDenso*
for an injector - 89-91 13B T high oval center 550cc purple 195500-2020
A bit pricey but they fit perfectly - difficult to even get off...Arrow
pointing to the center tab.

It is also worth noting that the oval center connectors appear to be a
japanese only design - Toyota (and others) appear to have also
used them in the following engines 22RE, S3-FE, 4A-FE.  E.g camry
2001V6sedan looks like it uses the same NipponDenso connectors.

I picked up a set of oval style injector connectors meant for "Toyota
22RE 3S-FE 4A-GE" engines.
The connector style looked slightly different but fit perfectly.
One seller on ebay used to sell them regularly.

Some other possibilities:
http://www.rx7.com/store/rx7/fcfuel.html
AC Delco PT425 (GM dealer 12116252) - discontinued - will supposedly fit
oval center connectors.
NAPA  Echlin 2-18457

Some other possibilities:
  BMW 6113-1358-330,
  GP Sorenson part 800-9416
  Standard Ignition Corp. SK-25


Cheers
Cary

Its a Walbro type pump but it came from a 3rd gen.
I am not sure what the RX8 uses.
Thanks Cary for the injector chart. I will add it to the
list.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.