Subject: EFI Pump Alternatives -- WAS: Re: Aeromotive pressure regulator
From: Rotary Engine
Date: 3/3/2009, 12:45 PM
To: AAA Put this in the To box


  It is sometimes difficult to mount fuel pumps in AC wings.
  Most people don't do it. They mount the pumps on the firewall.

  Paul Lamar

  Paul,

  I'm just starting construction of my fuel tanks for a Zenith CH-640.
  I'm opting for a four wing tank system. I'll likely be using a 16b
  conversion,
  fuel injection based on your designs. With the discussion on-going about
  in tank fuel pumps and fuel return lines, I am asking if I need to make
  accomodation for anything special. Presently, my tanks have no provision
 for
  a fuel return or in tank pump. Would it be necessary to design in any of
 this
  stuff?

  Thanks, C. Smith

  Yes you might think of adding a large removable panel in the root
  ribs for internal pumps. The 640 has a nice thick wing for internal
  pumps. Looks like the tanks are in the leading edge. If not
  practical use two lines from each tank. One for feed according
  to the plans and one for return fuel.

  Paul Lamar

  Correction, I meant 13b engine.
  C. Smith--


 So the EFI system with a fuel return line would preclude the use of a
 fuel flow meter to  keep track of fuel used and burn, unless someone
 knows of a meter that subtracts the return flow?
 so with a 4 tank system, thats 8 fuel lines, and a tank selector valve
 ganged 4x4? 4 separate fuel pumps, and control wiring?
 No other way to do this? I'm bummin' out.

 C Smith

 Unfortunately that is one of the drawbacks of a fuel return system.

 With the 555 system all injector pulses rates and widths are the
 same so one can build a simple flow meter that consists of diode
 and large capacitor that will sum the pulse width and rate from
 one injector. That sum can be read by a digital voltmeter to give
 you a flow rate. It is calibrated with a pot so it can read
 out GPH to the nearest .01 gallon. Very simple. Computers systems
 do it the same way except they do it in software.
 I might build the diode, capacitor and pot into one of the PC
 boards. You have your choice of read outs. One can probably test
 the scheme on a car EFI system.

 Paul Lamar

Just a quick reminder (in case anyone forgot) that the rising-rate
vacuum-referenced fuel pressure regulators are intended to be 1:1 and
increase fuel pressure 1psi for every 1psi manifold pressure increase
to keep a *constant differential pressure*.

By design the differential pressure across the injector should be
constant at all times, irrespective of manifold vacuum or boost.

Ratios other than 1:1 exist, but those are generally for radical
supplemental fuel pressure regulators used when applying forced
induction without any other means of fuel enrichment. With rates like
7:1, these are a fairly bad idea.


In other words, there is no necessary modification to a 3D fuel table
to take this action into account. The injectors can be assumed to
operate linearly (neglecting opening/closing time effects). Even if
the differential pressure was changing, there is no need to have a
separate fuel table and pressure sensor, as this information will be
incorporated into the 3D map when the engine is tuned.



Paul: Regarding flow measurement from injector pulsewidth, remember to
consider injector dead time (opening/closing) which becomes very
significant at low duty cycle or high RPM. Different injectors have
different properties in this department, which vary with applied
voltage.


-Chris

No computer. No 3D maps. The load on an aircraft engine never varies
with fixed pitch prop load. It is a much simpler system than a car
engine.

If we don't use a rising rate regulator the engine might be too rich
on the bottom end. I am just using it to supplement the linear mass air
flow sensor voltage controlled TLC 555. Just another way of tailoring
the curve. It may not be necessary.

I have a scope hooked up to monitor the dead times.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.