Subject: New slide throttle mechanism
From: Rotary Engine
Date: 3/15/2009, 10:54 AM
To: AAA Put this in the To box <rotaryeng@earthlink.net>, Larry Childs <larry@designitprototype.com>



  Larry has come up with a new way to
  actuate Teflon slide throttles for P-port engines.
  Slide throttles cut the internal aerodynamic drag
  of intake manifolds to a minimum... minimizing the fuel
  burn and maximizing the horse power. Butterfly throttles
  plates have undesirable aerodynamic drag.

  This design cuts down the overall length of the slide at some
  additional cost. Also the throttle cable travel and force can
  be changed by changing the length of the lever.

  Looks cool and incorporates the new skinny injectors
  holders such as the RX8 (Denso) and Siemens, pico or
  Bosch (Ford).

  -------------------------------------------------------

  Here is some interesting background info on Teflon.
  http://whitetrout.net/Chuck/Teflon/teflon.htm

  One of the most expensive parts of this slide throttle
  is the solid Teflon slide itself. I had an idea of looking into
  what it would take to coat an aluminum slide. A Teflon
  coated aluminum slide could be thinner saving some weight
  and cost. Just like a Teflon coated frying pan but with
  Teflon on both sides and the edges. Mikuni slide throttle
  carbs use Teflon coated slides.

  Perhaps a Teflon coated housings for an even lower coefficient
  of friction. Teflon on Teflon.

  One needs a low coefficient of friction in this
  application as when you close the throttle and the engine
  is driven by the prop the manifold pressure can be pumped down
  to minus 15 psi. With about 13 square inches of total area on the slide
  the clamping force could be as much as 13 x 15 or 195 pounds jamming
  the slide closed. Here is where Teflon's low coefficient of friction
  (.06) comes into play. 0.06 times 195 pounds is 11 pounds. That means
  the force on the throttle cable under prop wind milling conditions would
  be a max of only 11 pounds. I suspect Teflon on Teflon would
  be lower still.

  This is easy to check. Buy a frying pan, saw it up and put the Teflon
  sides back to back. Apply a known load and see how much force it takes
  to move one part laterally relative to another.
  Any volunteers to do this project?

  Coating metal with Teflon appears to be easier than it looks.

  http://www2.dupont.com/Teflon_Industrial/en_US/products/product_by_name/teflon_ptfe/aqueous.html


Paul Lamar



Paul,
Look up teflon bar @ McMaster Carr. http://www.mcmaster.com/#8735k28/=10imy3
A 1/4" x 4" x 12" bar is $38.23. They will also cut to length. Other sizes also available.
I see this as a relatively easy way vs making an alum part and then coating.
An alternative is teflon impregnated fiberglass tape to bond to your alum slide
(silicone adhesive already applied). http://www.mcmaster.com/#76495a29/=10iqoy
Dan F


It certainly is an easy way and that is what we are doing now.
We need 3/8" thick for strength reasons and that is quite a bit
more expensive.

Paul Lamar

Paul,
Yes cost is higher, but not much.  http://www.mcmaster.com/#8735k35/=10jc9c
Higher volume could reduce costs.   Will there be a central "go to" person
for this system, similar to Jerry Hay for engine mounts?
Dan F

Contact Larry for price and availability.

Larry Childs <larry@designitprototype.com>

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.