Subject: New slide throttle mechanism
From: Rotary Engine
Date: 3/15/2009, 9:18 AM
To: AAA Put this in the To box


 Larry has come up with a new way to
 actuate Teflon slide throttles for P-port engines.
 Slide throttles cut the internal aerodynamic drag
 of intake manifolds to a minimum... minimizing the fuel
 burn and maximizing the horse power. Butterfly throttles
 plates have undesirable aerodynamic drag.

 This design cuts down the overall length of the slide at some
 additional cost. Also the throttle cable travel and force can
 be changed by changing the length of the lever.

 Looks cool and incorporates the new skinny injectors
 holders such as the RX8 (Denso) and Siemens, pico or
 Bosch (Ford).

 -------------------------------------------------------

 Here is some interesting background info on Teflon.
 http://whitetrout.net/Chuck/Teflon/teflon.htm

 One of the most expensive parts of this slide throttle
 is the solid Teflon slide itself. I had an idea of looking into
 what it would take to coat an aluminum slide. A Teflon
 coated aluminum slide could be thinner saving some weight
 and cost. Just like a Teflon coated frying pan but with
 Teflon on both sides and the edges. Mikuni slide throttle
 carbs use Teflon coated slides.

 Perhaps a Teflon coated housings for an even lower coefficient
 of friction. Teflon on Teflon.

 One needs a low coefficient of friction in this
 application as when you close the throttle and the engine
 is driven by the prop the manifold pressure can be pumped down
 to minus 15 psi. With about 13 square inches of total area on the slide
 the clamping force could be as much as 13 x 15 or 195 pounds jamming
 the slide closed. Here is where Teflon's low coefficient of friction
 (.06) comes into play. 0.06 times 195 pounds is 11 pounds. That means
 the force on the throttle cable under prop wind milling conditions would
 be a max of only 11 pounds. I suspect Teflon on Teflon would
 be lower still.

 This is easy to check. Buy a frying pan, saw it up and put the Teflon
 sides back to back. Apply a known load and see how much force it takes
 to move one part laterally relative to another.
 Any volunteers to do this project?

 Coating metal with Teflon appears to be easier than it looks.

 http://www2.dupont.com/Teflon_Industrial/en_US/products/product_by_name/teflon_ptfe/aqueous.html


Paul Lamar

-------------------------------------
Paul,

There is a technology that would be better than Teflon, "Near Frictionless
Carbon" that has a coefficient of friction of ~0.004 as opposed to Teflon's
0.04.  I have enclosed a PDF of a writeup on it, I know that two companies
have licensed the technology, but I don't know their status on making parts,
whether they want large manufacturing base for parts, or can make evaluation
samples. The contacts for the companies are shown below.

Mark Dorbeck
Galleon International Corp
4204 Pleasant Valley Rd
Brighton, MI  48114
mdorbeck@galleonintl.com



Gary Lake, President
CemeCon USA,
500 IST Center,
Suite 1
Horseheads, NY 14845.
Gary.Lake@CemeCon.com


Bill Schertz
KIS Cruiser #4045
N343BS


Thanks Bill.
That is REALLY interesting. One tenth of Teflon!!!
The pdf was 1998. I wonder why we have not heard more
about it. DLC is widely used in Formula 1 and other race
engines. In fact it is used in the Mazda RX8 engine.

I'll copy them this email.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.