Subject: pport tuning peculiarity]
From: Rotary Engine
Date: 3/18/2009, 11:35 AM
To: AAA Put this in the To box


  Hello Paul-

  Sent this to Tracy earlier today; thought I would pass it along in case
  someone on the list has seen this before...

  Had some peculiar behaviors in that latest tuning attempts. Hopefully
  you'll have some suggestions.

  Background-

  - 13b, p-ported, with slide throttle design & "tuned" intakes
  - LS1 injectors
  - EC2 with latest p-port firmware
  - EM2
  - 6800 field altitude
  - 55F OAT
  - Known to be under propped (has a 72x72 160hp 2-bladed prop. Needs a
  72x109 230hp 3-bladed prop)

  Symptoms-

  If we run the engine with the manifold pressure lines *DISCONNECTED
 *from
  the EC2:

  - Engine starts very easily
  - The engine runs quite smoothly across a pretty wide rpm band after
  tweaking the manual mixture control.
  - Reasonably smooth running as low as 1500rpm engine (526rpm prop!)
  - Very smooth running 3000 - 4800 RPM.
  - Above 4800 rpm we seem to "run out of enrichen" on the manual mixture
  control & the engine stops.
  - MAP table view on the EM2 real-time shows the EC2 using map location
  59
  or 91 (MP constant matching atmospheric pressure) depending on high/low
  throttle (as expected)

  If we run the engine with the manifold pressure lines *CONNECTED *to the
  EC2:

  - Engine noticeably harder to start
  - Engine will not run smoothly at any rpm
  - Significant surging pattern -- rpm increases rapidly, followed by
  engine stumble to low idle rpm, followed by next surge.
  - Engine often stops during the stumble / hard to restart
  - MP pressure varies rapidly based on engine rpm
  - Significant manual mixture changes can help ease the surges somewhat,
  but never enough to get the engine to smooth out enough to let us see
  if MAP
  values could be tweaked.

  Looking at the MAP table with engine off, it seems like all map cells
 are
  at
  0 -- as expected. I did not check all 127 cells, only the top cells (say
  100 - 127).

  Mark (Rocky Mtn High)

  That is good evidence the 555 system will work fine :)

  We noticed this phenomena on the dyno test of your engine.

  I am not privy to Tracy source code but the last time I talked to him
  about it was a couple of years ago and he was taking only one sample
  of the intake manifold pressure per e-shaft revolution.

  Using a computer this takes only about 10 usec.
  http://en.wikipedia.org/wiki/Microsecond
  Light travels only one mile in FIVE microseconds.

  That is 10 millionths of a second. 100 usec is one msec or one thousands
  of a second. This is a very brief period of time so the manifold
 pressure
  is jumping around a lot in a p-port tuned manifold. It could be anything
  or even above atmospheric pressure at some times. That is what p-port
  tuned
  manifolds do. See the enclosed chart. A lot depends on WHEN you sample
  the pressure. It changes with RPM in unpredictable and mysterious ways.

  IMHO this is confusing the heck out of Tracy's computer. IMHO you need
  to feed the manifold pressure from both intake tubes past the slide
  throttle
  using very small hoses into a beer can and then tap out of the beer can
  with
  one normal size hose going to the pressure sensor in the computer.
  Hopefully
  this will damp the pulsations and average the intake manifold pressure.

  Al Gietzen tried this as I recall and it did not seem
  to change anything. I don't know what size hose Al used
  but I think very small hose is essential. On the order of .030
  inside diameter or smaller.

  Paul Lamar

  Mark,
  You don't need the beer can. If you use 1/8 od tubing, make a coil of
  tubing
  using at least 20 feet of tubing. 30 feet may be better. The length of
  tubing works to damp the intake signal to something that the computer
  makes
  sense with. My experience is the tubing can work better than a reservoir
  as
  it is using the friction of air molecules on the surface of the
 tubing as
  the damper, and will respond faster than a reservoir, but still be
 damped.
  That doesn't mean the maps are correct, as it sounds like the manifold
  pressure side of the map is way off.
  To trouble shoot being rich or lean, have a squirt bottle of fuel handy
  and
  give the runners a quick squirt as the rpms are declining (while
 surging).
  If this makes them instantly recover, the system is going lean. if it
  forces
  it to die, the system is going rich. that will tell you which way to
 go in
  the tuning. My guess is it is very lean with the sensor connected. The
  sensor disconnected simulates wide open throttle with no manifold vaccum
  with high fuel demand, so the ecu increases the pulse width to the
  injectors. When the sensor is connected, and the ecu sees manifold
 pressue
  decreased, it reduces the pulse width.
  make sure you are careful when performing this test...... and of course
  you
  have a fire bottle handy...
  hope this helps,
  Larry

  Hi Larry,

  20 feet of tubing is a fair size expense and bundle.
  My lathe tail stock chuck will not hold a tiny .030 dia. drill or I
 would
  make some orifice up and send them to Mark.
  Perhaps you could make up some orifice that will plug into
  red silicone vacuum plumbing tubing. OD of the orifice would be .125 to
  fit
  the tubing. 0.030, .025 and .020 ought to cover it.

  The rest of the world uses mass air flow sensors for a good reason :)

  Paul Lamar

  Paul,
  If you need a .03 orifice I would suggest going to local motorcycle
  aftermarket
  shop and checking their selection of carburetor pilot jets. If I recall
  correctly I'd check a Kehin size 20 or 25 pilot jet. That should be
 around
  .030 inches.
  Bill Jepson


  Good idea bill.
  Carb jets would be a gold mine of tiny orifices.


  Paul Lamar


 Paul,
 the small needle valves sold at hardware stores for use on small tubing
 would give you an adjustable orfice for developement work.
 Larry

 Another great idea. Are you listening Mark?

 Paul Lamar

You might also consider using the (unused) oil injector holes - I can't
remember what size they are.
That area might provide a slightly less erratic MAP source.
Plus you may be able to get a true VE-Volumetric Efficiency number.  The
measure value would need to reduced (based
on calculations) to compensate for compression in the chamber.
Cheers
Cary

Depends on when you do it. Since the computer does it in 10 usec
it is only a point in time.

Here is a question for everybody. Assuming you can only sample
the intake manifold pressure once per revolution of the e-shaft where on
this curve would you choose? I chose to do it 135 degrees after
top dead center. The red X marks the spot. Of course the shape of the
curve changes drastically with RPM because the intake is tuned for
only a narrow range of RPMs.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.