Subject: Video of First Flight - Mustang II w/ 13B Rotary Engine
From: Rotary Engine
Date: 4/3/2009, 8:22 AM
To: AAA Put this in the To box


   If you are interested, there is a video of my first flight at this
link.
   http://www.eaa1246.org/videodisplay.asp?id=36

   I have a lot of good friends who helped me make the event a success.
   They took pictures and video and were there to support me.

   I did my second flight yesterday and all went well.  The landing was
   much better.


   Bob

   That did not work for me Bob.
   I am running Thunderbird.
   If you mail it to me on DVD I can put it on the ACRE web site
   in wmv or some other common format such as mov.
   Mail it to:
   830 East Santa Maria St.
   Suite 303
   Santa Paula CA
   93060

   A lot of sites have problems with different browsers.
   Youtube seems to have it figured out as just about
   any browser can view Youtube.

   -----------------------------------------------
   I see what happened. The EAA site did not inform us it was
   downloading. It took awhile but eventually the video appeared
   on the screen.

   Nice editing. I am glad we got to hear the engine sound.
   Did you have any problems with the CG? The nose looks a bit long.

   Paul Lamar

   Yes, the nose is longer than usual. I moved the seats back some and
   added additional baggage space behind the seats, which called for
more
   weight on the nose.  Based on my original W&B estimates, that is
where
   the engine should have been placed.  It gave me enough room to place
the
   radiator and oil cooler between the engine and firewall.   As it
turned
   out, the plane was slightly nose heavy with the battery on the
firewall,
   so I repositioned the battery in the tail.  Now the W&B is perfect.
As
a
   bonus, the battery is out of the engine compartment where it would
have
   gotten a lot of heat and there is more room on the firewall for
cooling
   air to exit.  So far, I have been able to idle on the ground for over
25
   minutes without any overheating.  My cowl flap can be opened wide or
   closed to adjust for temperature needs.  Even on climb out, the
engine
   barely got up to operating temp (180 degrees) with the cowl flap half
   open.  Yesterday, I closed the cowl flap completely and ran the
engine
   up to about 32 inches of manifold pressure (3/4 throttle) and got 190
on
   water temp after about five minutes.  Speed was only 170 mph at 3,500
   feet and OAT was 55 degrees F.  When it gets hot during the summer
   months, cooling may be marginal at high power settings.  With the
turbo,
   I should be able to fly at higher altitudes where it is cooler and I
can
   go faster.  Time will tell.  Right now, I am happy just to be flying
   instead of building.

   Bob

   Thats great Bob. Yes the OAT is a little low for a good test.
   Bravo on the cowl flaps. I have been harping on that for years :)
     Also what are you using for an oil cooler?

   What kind of turbo is that? If stock 1988 to 1992 Mazda I suggest
   a turbo tach kit from Garret to keep from over speeding it
   at altitude. The 1991 seem to last about two hours at 12,000 feet
   as a rough guide. Just about everybody that has tried one has
   blown it up including Mistral. The suggested modification is
   take some meat off the tops of the turbine blades after you install
   the tach for a base line data. This has the effect of reducing the
   centrifugal
   forces on the blades and will slow it down as well. Most auto turbos
   are over powered for rapid spool up.  I think as a wild ass guess it
   should be kept below 90,000 RPM.

   Paul Lamar


   The oil cooler is stock Mazda that came with the 1987 Turbo 13B RX-7
   engine.  The turbo is not stock.  It is a much bigger Turbonetics
60-1
   with an external waste gate and stock intercooler.  The turbo does
not
   start to generate much boost until I get to the top end of engine
rpm.

   Bob

   Ah so very good. I won't worry  then.
   Thanks for the info Bob. Keep us informed on how it goes.

   Paul Lamar



Bob do you have provision for logging turbine inlet temps by power
setting
for each mission flown?

Steve Beckham


Steve,

I have a temperature gauge in the intake manifold (after the turbo and
after the intercooler) to monitor intake air temps and I have a manifold
pressure gauge to monitor power settings, but I do not have any
automatic logging system.  I guess I could manually write down the
measurements, but so far, I have been too busy checking the basic flying
qualities of the airplane to be concerned with those details.  I also
have a knock sensor which sends a ping signal to my headset and I got
one or two of those when I advanced power with too lean of a mixture.  A
quick turn of the mixture rich knob fixed that.  The air/fuel gauge
(hooked up to an oxygen sensor in the exhaust downpipe) also tells me
when the engine is running too lean.

When I get further along in my test flights, I plan to record more
information on engine parameters and performance.

Bob

Hi Bob,
The knock sensors you refered to, are they (or is it) the standard Mazda
issue? How many knock
sensors do you monitor? Can you detail for us the circuitry you use to
bring the warning to your
headset? The standard issue sensors are lead into the ECU harness to
retune engine parameters and
I'm unable to determine how to utilize the signal. It's one of those
sounds that a pilot never wants
to hear but having the ability to do so can add to peace of mind. I'm
still planning to monitor
inlet temp also. Thanx, Dave M


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.



The knock sensor is from MSD Ignition, part # 8964.  For more details,
see http://tunertools.com/proddetail.asp?prod=MSD-8964  I think Summit
Racing has them for sale at about $250.  I bought mine in 2003 for $160.
Attached are the installation instructions from MSD.  The sensor screws
into the stock knock sensor fitting on my 1987 13B Turbo Mazda rotary
engine, which is just below the oil filler pipe on the center housing.
There is a small speaker (with volume control) in the knock sensor box.
I spliced the wires going to that speaker to an auxiliary input in my
intercom, so that I can hear the pings created by the knock sensor.
There is also an LED display on the box that shows the level of knock.
I tested the system by tapping on the engine with a hammer.  It works
great.

Bob


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.