Subject: Video of First Flight - Mustang II w/ 13B Rotary Engine
From: Rotary Engine
Date: 4/7/2009, 2:10 AM
To: AAA Put this in the To box


 Bob, of interest is the long term effect of the rotary's exceptionally
high
 exhaust gas temperatures on the turbo as a result of sustained high
power
 settings above 75% power.
 ----- Original Message -----
 From: "Rotary Engine" <rotaryeng@earthlink.net
 To: "AAA Put this in the To box" <rotaryeng@earthlink.net

 If you are interested, there is a video of my first flight at this
 link.
 http://www.eaa1246.org/videodisplay.asp?id=36

 I have a lot of good friends who helped me make the event a success.
 They took pictures and video and were there to support me.

 I did my second flight yesterday and all went well.The landing was
 much better.


 Bob



 Nice editing. I am glad we got to hear the engine sound.
 Did you have any problems with the CG? The nose looks a bit long.

 Paul Lamar

 Yes, the nose is longer than usual. I moved the seats back some and
 added additional baggage space behind the seats, which called for more
 weight on the nose.Based on my original W&B estimates, that is where
 the engine should have been placed.It gave me enough room to place
 the
 radiator and oil cooler between the engine and firewall. As it
 turned
 out, the plane was slightly nose heavy with the battery on the
 firewall,
 so I repositioned the battery in the tail.Now the W&B is perfect. As
 a
 bonus, the battery is out of the engine compartment where it would
 have
 gotten a lot of heat and there is more room on the firewall for
 cooling
 air to exit.So far, I have been able to idle on the ground for over
 25
 minutes without any overheating.My cowl flap can be opened wide or
 closed to adjust for temperature needs.Even on climb out, the engine
 barely got up to operating temp (180 degrees) with the cowl flap half
 open.Yesterday, I closed the cowl flap completely and ran the engine
 up to about 32 inches of manifold pressure (3/4 throttle) and got 190
 on
 water temp after about five minutes.Speed was only 170 mph at 3,500
 feet and OAT was 55 degrees F.When it gets hot during the summer
 months, cooling may be marginal at high power settings.With the
 turbo,
 I should be able to fly at higher altitudes where it is cooler and I
 can
 go faster.Time will tell.Right now, I am happy just to be flying
 instead of building.

 Bob

 Thats great Bob. Yes the OAT is a little low for a good test.
 Bravo on the cowl flaps. I have been harping on that for years :)
 Also what are you using for an oil cooler?

 What kind of turbo is that? If stock 1988 to 1992 Mazda I suggest
 a turbo tach kit from Garret to keep from over speeding it
 at altitude. The 1991 seem to last about two hours at 12,000 feet
 as a rough guide. Just about everybody that has tried one has
 blown it up including Mistral. The suggested modification is
 take some meat off the tops of the turbine blades after you install
 the tach for a base line data. This has the effect of reducing the
 centrifugal
 forces on the blades and will slow it down as well. Most auto turbos
 are over powered for rapid spool up.I think as a wild ass guess it
 should be kept below 90,000 RPM.

 Paul Lamar


 The oil cooler is stock Mazda that came with the 1987 Turbo 13B RX-7
 engine.The turbo is not stock.It is a much bigger Turbonetics 60-1
 with an external waste gate and stock intercooler.The turbo does not
 start to generate much boost until I get to the top end of engine rpm.

 Bob

 Ah so very good. I won't worry then.
 Thanks for the info Bob. Keep us informed on how it goes.

 Paul Lamar



 Bob do you have provision for logging turbine inlet temps by power
 setting
 for each mission flown?

 Steve Beckham


 Steve,

 I have a temperature gauge in the intake manifold (after the turbo and
 after the intercooler) to monitor intake air temps and I have a
manifold
 pressure gauge to monitor power settings, but I do not have any
 automatic logging system.I guess I could manually write down the
 measurements, but so far, I have been too busy checking the basic
flying
 qualities of the airplane to be concerned with those details.I also
 have a knock sensor which sends a ping signal to my headset and I got
 one or two of those when I advanced power with too lean of a mixture.A
 quick turn of the mixture rich knob fixed that.The air/fuel gauge
 (hooked up to an oxygen sensor in the exhaust downpipe) also tells me
 when the engine is running too lean.

 When I get further along in my test flights, I plan to record more
 information on engine parameters and performance.

 Bob

 This is another use for a cheap handheld camcorder..I posted a link a
 couple of days ago.Mount the cam such that it has a clear view of the
 instrument panel.After the flight, download the file to your favorite
 computer, watch it video, and transcribe any data you are interested
in toa
 spreadsheet..


 Matt-

 Bob, of interest is the long term effect of the rotary's exceptionally
high
 exhaust gas temperatures on the turbo as a result of sustained high
power
 settings above 75% power.

 Steve Beckham


Bob, I'm very curious to what size the turbine housing is? 1.0 or
better?

Very nice job Bob.

thanks Skip
-- 
Skip,

The turbo is a Turbonetics T04B, Model 60-1, with a "Big Shaft" (for
less stress on the bearings).  The housing has a divided tang with "P"
trim.   AR is 1.15.  Wastegate is an externally mounted Deltagate Mark
II, which can be set to provide between 3-5 lbs of boost.  I also have a
panel mounted, manually controlled, regulator that can increase the
boost up to an additional 10 lbs.  See
http://www.turbocharged.com/main.htm Click on the catalog link and then
on the Turbocharger link.  The compressor map shows that this turbo will
spin at 70-80 thousand rpm with 5-10 lbs of boost for the airflow
produced by the Mazda 13B rotary.

Bob

What airflow number are you using Bob.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.