Here are a few charts from Heinz Heislers book Advanced Engine
Tech and others. The first chart shows that; as the fuel air ratio gets
real lean and the pressure lowers in the combustion chamber
at high altitude the voltage required to fire the plugs goes up.
Klaus has exploited this situation to lean his engine out
at high altitude and improve the BSFC to remarkable levels
by increasing the spark voltage. He has achieved as much as
100 MPG at 130 MPH and 60 MPG at more reasonable cruising speeds.
This is a piston engine where the spark plugs are at one end
of the fire and the piston is at the other end.
In our case we have a moving combustion chamber where the fire
travels along side the spark plugs for quite some time. IMHO We want
the spark plugs to continue to fire for as long as the unburned
and burning mixture is still present moving past the plugs. That takes
8.3 ms at six thousand RPM cruise RPM. See chart 2.
A capacitor discharge ignition system is very good at firing
spark plugs fouled with 100 LL but it only fires for .2 ms. Even
an inductive system (Chevy LS1 coil) or stock Mazda ignition
only fires for about .8 ms.
IMHO NO WHERE LONG ENOUGH FOR WHAT WE NEED!
IMHO we need an ignition system to fire for 8.3 ms or 300 degrees.
TEN times as long. MSD makes a multiple spark capacitor
discharge ignition system widely used by Mazda rotary
engine racers but it only works up to 3000 RPM. After that it
is "one strong spark" says MSD. Not enough in IMHO. This is why
I am doing a m.s.d. ignition system with several pre-charged
capacitors fired in rapid sequence by a cheap single chip computer.
I hope this is a break through in improving the BSFC of
the rotary engine. I think it is worth a try.
Patent applied for :)
--------------------------------------------------
This is the range of rotor positions I intend repeatedly firing the
spark
plug. Mostly the leading plug (lower plug) as one does not want to risk
igniting the mixture in the following chamber.
Paul Lamar
Good going Paul. We need the long duration. Will be very interesting.
Sure wish we access to the Mazda factory development notes and a
supplyof
the three sparkplug rotor housings the Mazda factory built for the R26B
LeMan's engines to improve efficiency.
Steve Beckham
Steve,
Heck I would just like to be able to buy factor P-port housings for a
reasonable price!
2 plug or 3 I don't care.
<snip
Bill Jepson
Paul, wasn't there an offer at one point to get the serious MazdaSpeed
race parts discounts?
I'm sure you're aware that the MFR Pports are still orderable - not sure
which versions. I emailed a few folks.
Apparently, the R26B Pport, 3 plug housings were listed with MazdaSpeed
Japan, but were not available outside of serious racing.
Nagoya Precision in Japan can apparently do the third plug mod. I also
read that JHB and Carlos Lopez? does them as well.
Cheers
Cary
I contacted John Doonan on the parts discount and he said he would get
back to me.
The sure fire thing is buy an old RX7 and enter a gymkhana or two.
I suspect they are not going to honor us homebuilders that
are doing R&D and building our own engines. It is kind of a shame as
we are spreading the knowledge of how to over haul rotary engines.
You won't find that at your average Mazda dealer. The more knowledge that
is out there about rotaries in the long term help RX8 sales.
Nothing more discouraging than driving into an auto repair
shop with a rotary problem and trying to get it fixed when the
mechanic says he knows nothing about rotaries. The truth is they
are extremely easy and fast to overhaul compared to any piston engine.
Maybe we can get race parts through Mears Mazda in
http://www.mearsmotors.com/
They offered to give us a discount if you mention the newsletter.
The owner Bob Mears is building a scale spitfire powered by a 3 rotor.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.