Subject: 2nd gen mass airflow sensor. Low cost.
From: Rotary Engine
Date: 5/16/2009, 8:14 PM
To: AAA Put this in the To box

 snipes:

 The airplane operating requirements are relatively simple
 compared to
 that of a performance car like a Corvette. In the
 Corvette, they want
 good throttle response at all RPM, and good fuel economy
 with very
 minimal driver involvement - one lever. On the other hand,
 the
 airplane really has only a couple of requirements.. It
 can't quit.
 It can't burn too much fuel in cruise. It has to make
 the peak
 horsepower afforded by the mechanical limits of the engine.
 That's
 not too bad by comparison. The airplane engine doesn't
 have to idle
 all that well as long as it doesn't actually quit. It
 can have a
 separate lever for controlling power vs. economy. All of
 this makes
 the tunability of the airplane easier to accomplish by
 comparison.

 As far as running the engine on the dyno, I think that was
 a p-port,
 and it was being run with the manifold pressure tap located
 at the
 wrong place on the engine for good readings. It would be
 interesting
 to hop on the dyno with the mp tap installed in the housing
 and see
 how the tuning goes.


 Regards,

 Matt-

 Looks fixed to me. This looks fine.

 Paul Lamar


 Wonderful response Bill. I would add that the choice
 between carb, mech
 fi,
 efi, distributor, dis, etc boils down to not only
 simplicity but also
 cost.
 This wouldn't be the case in the certified market but
 since we don't
 have
 to
 jump hops for the FAA, we can choose our options based on
 more than
 just a
 certificate. With regards to fuel delivery, it seems like
 the only two
 cost
 effective options are the Holley and custom efi (555,
 Tracy's,
 Megasquirt.)
 If someone could find a better carb in terms of function
 and cost, that
 would be cool but at this point that seems very unlikely.
 Mech fi
 would be
 a
 very good feature if it wasn't SO expensive. For $2900
 I could buy a
 Motec
 (read $$$) and still have money left for dyno tuning. While
 custom efi
 would
 be the holy grail of performance and flexibility, how many
 people
 really
 need it? The turbocharged and the aerobatic (are there any
 using
 Mazda's?)
 could genuinely use them, for everyone else, seems
 unlikely.
 Vlad
 --


 My problem with electronic FI is in the systems support..
 Requires
 independent, redundant power (dual alternators), and high
 pressure
 fuel. Not insurmountable by any means, but I'm not
 convinced the
 payoff is worth it for what I want to be flying.


 Matt-

 It's part of the risk that one must accept when
 building or flying an
 experimental aircraft or using a non-certified engine. Am
 I against
 making
 the systems safer and less likely to cause a catastrophic
 failure, no.
 But
 I'm not asking an engine from a car to be as redundant
 and rudimentary
 (read
 safe) in design as a $25k+ aero engine. Would I fly an efi
 rotary with a
 single alternator, battery, ecu, etc., yes. If I was that
 concerned about
 safety, I would get a certified slug and call it a day.
 Vlad

 To interject a disrupting thought. I have a Bosch CIS fuel
 injection
 running on a rotary in an airplane. Al thought the plane
 has not flown(
 a problem with me not the plane), the injection was
 extensively tested
 on the ground on a test stand. The CIS is a mass flow
 sensor with
 automatic mixture adjustment. In addition the mixture can
 be
 modified to any level from too rich to run to too lean to
 run. All the
 hard work of air verses fuel has been done at time of
 manufacture of the
 unit.
 The units are very inexpensive from a junk yard. I have
 several that I
 have used on cars that were no where worn out. A little
 clean up and
 they work perfectly.
 However they are not without problems.
 1. Size is a problem.
 2. High pressure fuel.
 3.Weight might be a problem. They are not light because of
 the cast iron
 fuel distributor.

 C Smale

 I was going through my records, the MAF I purchased new from Rock Auto was
 $61, ('02 5.4l V8) didn't have to hunt through junk yard, just type on
 keyboard, no time spent removing, or driving to junk yard, or cleaning and
 reconditioning. ABS sensors, $22 ea, same conditions, with added benefit
of
 not laying on my back in the mud or getting crud in my face removing them.

 Time spent researching part numbers and tracking down flow data for
suitable
 injectors so far I've put in maybe 4-5 hrs. I have decided it is easier to
 just buy some 42 lb ford racing injectors(known qualities), set of 8 for
 $210, that's $26.25 ea. free shipping. Anyone want the other 4?
 That's under $300 so far. I figure, maybe another $200 for the rest of the
 electronic 555 parts and circuit boards. Fuel runner and regulator,
haven't
 priced yet, can't be that much.
 I figure the rest of the intake stuff like tubes and slide throttle would
be
 necessary no matter how you skinned the P-Port cat, so those costs are
 comparably the same.

 Because of differences in the MAF and injectors anyone decides to use(or
 carburators, and differences in how you make your induction setup), I
agree
 that anyone choosing to go rotary should be prepared to put in tuning
time.
 Everyone has to do it, so it is not a differentiating factor. I REALLY
like
 the FI systems resistance to icing.
 I dont think hardening the electronics is going to be difficult, I plan on
 using an appropriately sized MOV and LM-150K (proven and reliable,
 inexpensive) in front of the control circuitry.
 I really can't see any substantial cost difference in either approach.
 Your results may vary.
 C. Smith

 As far as having two power sources for an EFI airplane, my thought is that
 instead of having two alternators, have two batteries-  by a new one every
 year and rotate the oldest one out. I have two  Powersonic 28 amp/hr
 batteries that are sealed saturated fiberglass mat, cost about $50 each.
If
 the alternator goes out, I have enough juice in the two batteries to fly
 quite a ways to a safe landing strip. A  charged battery in good condition
 is one of the most reliable power sources around.


 Brian Trubee

 Brian, that is how Cessna has set up their G-1000 aircraft, although
 rotating batteries wasn't part of the maintenance plan. They use a split
 bus, essentials on one, everything else on the other. A complete charging
 system failure would still leave you with a 45 min reserve battery to
power
 one display at some reduced capability. I feel quite comfortable with
 electronics, and a well thought out electrical system architecture. There
is
 a fellow named Bob Knuckolls, runs a list called Aeroelectric Connection.
 His book and website cover just about any set-up you could envision, and
he
 answers questions with factual information backed up with well researched
 documentation.

 I think proper battery testing (yes, there is a right way to load test
that
 allows you to not have to just buy batteries on a fixed schedule) is
 reliable enough and well proven, so I would be comfortable with a dual
 battery, single alternator, split bus system.

 When I get to the point of final board design, I'll consider a few
different
 back-up/emergency systems for the FI. I will share that when it happens
down
 the road.
 C. Smith


All well and good..  Testing batteries, changing batteries, etc.
However, dual alternators is less maintenance which equals more flying
and less fiddling.  How many batteries will you replace before meeting
the cost of the second alternator?

At the power consumption of a complete EFI system, how big does the
battery need to be to support flight to the exhaustion of fuel on
board?  Having to land within 45 min of electrical failure while
there's still fuel in the tank is not a good design choice for a
traveling airplane.  Especially if you plan to fly anything but clear
VFR.  If you don't care about weather flying, that's fine, it just
doesn't satisfy what I'm going for.


Matt-

Let's address all those questions, one at a time.

How many batteries will you replace before meeting
the cost of the second alternator?

Can you tell me how much the second alternator architecture you are thinking
of costs vs a single alternator single battery architecture?
Given that all batteries should be load tested annually, or if you subscribe
to the replace at intervals, (I'm hoping no one subscribes to the use till
failure system) any given scenario is a two battery system will be replacing
2 batteries on average over a battery lifetime. How does the price of
batteries compare to your dual alternator? I can't answer that if you don't
tell me what your dual alternator architecture costs.

At the power consumption of a complete EFI system, how big does the
battery need to be to support flight to the exhaustion of fuel on
board?

How much fuel do you have on board? What is the power consumption of your
EFI system? Is your emergency requirement MAX on board fuel? Wouldn't that
depend on your aircraft.

Having to land within 45 min of electrical failure while
there's still fuel in the tank is not a good design choice for a
traveling airplane.

I have to call your judgment on this one, I think the FAA considers an
electrical failure a cause for landing at nearest airport, and cause for
immediate landing. I'll carefully say that any pilot who would even consider
flying any further than the nearest landing in the face of a known
electrical system failure to be wreckless. [reckless? :)]

I have an instrument rating, and the G-1000 architecture meets certified IFR
requirements. Rhetorical questioning doesn't advance the body of knowledge.
If you have specific requirements, and already done your own cost analysis,
help me with the figures please.
C. Smith



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.