Subject: Engine Mount Request -- Bearhawk with 13B or 20B
From: Rotary Engine
Date: 6/9/2009, 8:48 PM
To: AAA Put this in the To box







--- On Tue, 6/9/09, Rotary Engine <rotaryeng@earthlink.net> wrote:

From: Rotary Engine <rotaryeng@earthlink.net>
Subject: Engine Mount Request -- Bearhawk with 13B or 20B
To: "AAA Put this in the To box" <rotaryeng@earthlink.net>
Date: Tuesday, June 9, 2009, 6:17 PM

  Paul,

  All the X & Y dimensions are from the flat
firewall.
  Note there are five mounting points. Designer call
for up
 to
  180hp with the four point, with up to 260hp with
five
  points.

  I'm trying to get an idea of the room using either a
13B
 or
  20B. Only one Bearhawk is flying (Elden Yates).
Little
  details, but Elden ended up putting his battery next
to
 the
  PSRU to get some weight out on the nose!

  Plan is to use Tracy Cooks PSRU.  With 180hp,
 Bearhawk
  cruise is 140mph, with 260hp it is at 160 mph (75%
on
 both
  numbers).

  --Tom

  There are five mounting points on the Bearhawk
Firewall.
  Firewall is
  approximately 2" larger at all mounting points.

  In Inches:                X        Y
  Lower Left        3.500   0.000    reference    Lower
Right        31.188   0.000           Upper
Left        0.000   20.188           Upper
Right        34.688   20.188           Upper
Middle        17.344   24.844                          THRUST
LINE        17.344   15.844    Firewall
  set back at 6 degrees (top towards tail).
                        Prop Flange (front
edge) to
 VERTICAL MOUNT -
  40.625"        Note, from
firewall (6
 degree lean back - top towards tail)
  is sin 6 *
  (Thrust Y position) or an additional
  1.656"            -- end of email ---


  Does this look right?

  Now you want me to lay it back 6 degrees?

  Paul Lamar


       Paul,

 The bottom measurement should be changed from 27.500 to
 27.688"

 Upper middle is 24.844" from the lowest two holes.

 Correct, rotate the firewall back 6 degrees. Point of
 rotation is from
 the lowest two points on the firewall.

 Thank You,

 Tom

 OK Tom Here it is.

 Paul Lamar


      Looks good.

Bob Barrows, the designer, doesn't have an email account!
No computer,
either! I suspect that is why he gets so much done.

Thanks,

Tom

I'll see Bob at OSH and show him some of this stuff.

Here are some preliminary 3Ds. Ask questions if you see
something
that looks strange. Upper motor mount is not in yet but we
will use a rubber ball jointed strut mount to above the
water pump.
Are you using and RX8 engine? That area differs from the
13B.

Paul Lamar


Paul,

Looks great!

I have not purchased an engine, so still discovery stage at this
point. Plan is either a RX8 Renesas so the exhuast lives, also
looking at 20B's.

Looking at approximate weight and distance from firewall to do some
preliminary W&B -- yes numbers we want to run past Bob.

Tom

There are two details that are different 13B verses RX8 engine.
Pan bolt pattern and details of the top mount on the center
housings. Here is the 13B version. I have an RX8 engine in the hangar
so I'll get a picture of that shortly.


The distance from the firewall to the CG of engine, gear-box, prop,
starter, alternator and muffler is 23.5 inches. Weight is on the order
of 280 pounds. Plus or minus 10 pounds.  You won't know exactly until
it is built but this beats a six cylinder by a long shot if you go P-port.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.