Subject: Engine Mount Request -- Bearhawk with 13B or 20B
From: Rotary Engine
Date: 6/10/2009, 7:45 AM
To: AAA Put this in the To box


  Paul,

  All the X & Y dimensions are from the flat firewall.
  Note there are five mounting points. Designer call for up
 to
  180hp with the four point, with up to 260hp with five
  points.

  I'm trying to get an idea of the room using either a 13B
 or
  20B. Only one Bearhawk is flying (Elden Yates). Little
  details, but Elden ended up putting his battery next to
 the
  PSRU to get some weight out on the nose!

  Plan is to use Tracy Cooks PSRU.  With 180hp,
 Bearhawk
  cruise is 140mph, with 260hp it is at 160 mph (75% on
 both
  numbers).

  --Tom

  There are five mounting points on the Bearhawk Firewall.
  Firewall is
  approximately 2" larger at all mounting points.

  In Inches:
    X        Y
  Lower Left        3.500
 0.000    reference    Lower Right
       31.188    0.000
        Upper Left
     0.000    20.188
      Upper Right
   34.688    20.188
    Upper Middle
 17.344    24.844

    THRUST LINE
 17.344    15.844    Firewall
  set back at 6 degrees (top towards tail).

         Prop Flange (front edge) to
 VERTICAL MOUNT -
  40.625"        Note, from firewall (6
 degree lean back - top towards tail)
  is sin 6 *
  (Thrust Y position) or an additional
  1.656"
  -- end of email ---


  Does this look right?

  Now you want me to lay it back 6 degrees?

  Paul Lamar


       Paul,

 The bottom measurement should be changed from 27.500 to
 27.688"

 Upper middle is 24.844" from the lowest two holes.

 Correct, rotate the firewall back 6 degrees. Point of
 rotation is from
 the lowest two points on the firewall.

 Thank You,

 Tom

 OK Tom Here it is.

 Paul Lamar


      Looks good.

Bob Barrows, the designer, doesn't have an email account! No computer,
either! I suspect that is why he gets so much done.

Thanks,

Tom

I'll see Bob at OSH and show him some of this stuff.

Here are some preliminary 3Ds. Ask questions if you see something
that looks strange. Upper motor mount is not in yet but we
will use a rubber ball jointed strut mount to above the water pump.
Are you using an RX8 engine? That area differs from the 13B.

Paul Lamar

Paul, am I interpreting the 6 degrees incorrectly...that the mount
has 6
degrees of upthrust?  Also, related question, on your mount design
that
Jerry has been welding, is the prop flange 90 degrees vertical?

Steve Beckham

No the BearHawk firewall is laid back six degrees. This mount has no
down
thrust or side thrust. The down thrust angle can be adjusted however
by
using left and right hand threads on the top strut.

Jerry's jig can accommodate down thrust and side thrust.

For the new guys we have been doing these motor mount designs for
about
the past seven years. A free service of the newsletter.

Paul Lamar



Paul,  Is the firewall leaning back a problem for strut angle?  Could
you design a bracket  to receive the strut that stands off the
firewall the amount required to get a good angle.  Jerry


I think you are talking about the more or less vertical strut.
In that case the answer is no in general as the firewall hard points
would have to accommodate a significant bending moment and that is
out of my control. In the case of the BearHawk the upper center
hard point is mainly designed for tension and compression so
that is why I am using it for a horizontal strut to the center
of the top of the engine. This strut will take about half the
prop thrust loads which can be as much as 500 pounds. Consequently the
the horizontal prop thrust loads on the lower front rubber bushings are
reduced by about 500 pounds. This is an improvement on the original design
done by Jim Griswald on the Questair Venture.

Steve Beckham and Everett Hatch used this configuration years
ago and it worked well as it was kept later by Power Sport that built
several airplanes. The main design challenge is the bracket that
bolts to the top of the center housing. Power Sport built the
bracket using an NC mill. I am working on a design built
from welded 4130.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.