Subject: Engine Mount Request -- Bearhawk with 13B or 20B
From: Rotary Engine
Date: 6/10/2009, 2:26 PM
To: AAA Put this in the To box


Paul,

All the X & Y dimensions are from the flat firewall.
Note there are five mounting points. Designer call for up
to
180hp with the four point, with up to 260hp with five
points.

I'm trying to get an idea of the room using either a 13B
or
20B. Only one Bearhawk is flying (Elden Yates). Little
details, but Elden ended up putting his battery next to
the
PSRU to get some weight out on the nose!

Plan is to use Tracy Cooks PSRU.  With 180hp,
Bearhawk
cruise is 140mph, with 260hp it is at 160 mph (75% on
both
numbers).

--Tom

There are five mounting points on the Bearhawk Firewall.
Firewall is
approximately 2" larger at all mounting points.

In Inches:
X  Y
Lower Left  3.500
0.000 reference Lower Right
31.188 0.000
Upper Left
0.000 20.188
 Upper Right
 34.688 20.188
Upper Middle
17.344 24.844

THRUST LINE
17.344 15.844 Firewall
set back at 6 degrees (top towards tail).

 Prop Flange (front edge) to
VERTICAL MOUNT -
40.625"  Note, from firewall (6
degree lean back - top towards tail)
is sin 6 *
(Thrust Y position) or an additional
1.656"
-- end of email ---


Does this look right?

Now you want me to lay it back 6 degrees?

Paul Lamar


Paul,

The bottom measurement should be changed from 27.500 to
27.688"

Upper middle is 24.844" from the lowest two holes.

Correct, rotate the firewall back 6 degrees. Point of
rotation is from
the lowest two points on the firewall.

Thank You,

Tom

OK Tom Here it is.

Paul Lamar


 Looks good.

 Bob Barrows, the designer, doesn't have an email account! No computer,
 either! I suspect that is why he gets so much done.

 Thanks,

 Tom

 I'll see Bob at OSH and show him some of this stuff.

 Here are some preliminary 3Ds. Ask questions if you see something
 that looks strange. Upper motor mount is not in yet but we
 will use a rubber ball jointed strut mount to above the water pump.
 Are you using an RX8 engine? That area differs from the 13B.

 Paul Lamar

 Paul, am I interpreting the 6 degrees incorrectly...that the mount
 has 6
 degrees of upthrust?  Also, related question, on your mount design
 that
 Jerry has been welding, is the prop flange 90 degrees vertical?

 Steve Beckham

 No the BearHawk firewall is laid back six degrees. This mount has no
 down
 thrust or side thrust. The down thrust angle can be adjusted however
 by
 using left and right hand threads on the top strut.

 Jerry's jig can accommodate down thrust and side thrust.

 For the new guys we have been doing these motor mount designs for
 about
 the past seven years. A free service of the newsletter.

 Paul Lamar



Paul,  Is the firewall leaning back a problem for strut angle?  Could
you design a bracket  to receive the strut that stands off the
firewall the amount required to get a good angle.  Jerry


I think you are talking about the more or less vertical strut.
In that case the answer is no in general as the firewall hard points
would have to accommodate a significant bending moment and that is
out of my control. In the case of the BearHawk the upper center
hard point is mainly designed for tension and compression so
that is why I am using it for a horizontal strut to the center
of the top of the engine. This strut will take about half the
prop thrust loads which can be as much as 500 pounds. Consequently the
the horizontal prop thrust loads on the lower front rubber bushings are
reduced by about 500 pounds. This is an improvement on the original design
done by Jim Griswald on the Questair Venture.

Steve Beckham and Everett Hatch used this configuration years
ago and it worked well as it was kept later by Power Sport that built
several airplanes. The main design challenge is the bracket that
bolts to the top of the center housing. Power Sport built the
bracket using an NC mill. I am working on a design built
from welded 4130.

-----------------------------------------------------

Here is the bracket for the 13B center housing with an exhaust heat
hole. The turbo 13B center housing does not have this hole
so it will require a slightly different bracket. This can be made in two
parts. The top part is 1/4 inch thick mild steel plate. The bottom
part is 3/8 th thick mild steel plate. They can be brazed together
as the lower plate should be a slip fit in the large hole. This
transfers the shear load directly into the cast iron housing and
not by the hold down 8 mm and 1/4 inch flat head screws.
The trust load from the prop is countered by a 1/2 inch all steel
ball joint with a half inch bolt. The reason for an all steel ball
joint on this end is they can accommodate higher mis alignment angles
and they are less affected by temperature than a rubber ball joint.
There will be a rubber ball joint on the firewall end to isolate
what little vibration there is from the rotary.

Ask questions or make comments in case I missed something.

Paul Lamar


Paul, these are the attach points used for the mount in the new RV-3.  Uses
conical Lycoming rubbers for steel piece we fabricated for right side and
aluminum other side.  But have a set of billet mounts for both new turbo
center housings and Gen II as well for future mounts for converting to
vertical attachment vs. horizontal bolts used on RV-3.  Most compact,
lightest configuration we did.  Didn't use the billet pieces for RV-3
because am using the quick and dirty mount and related pieces we built to
convert Alan's RV-3 @ Sun'n Fun in '97 to accept the Mazda conversion we
took out of the RV-4.

Steve Beckham

A set of jpgs came across but they were the ones I sent.
Can you send the RV3 jpgs again?

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.