I need some feed back from the pilots
out there that might be using the 555 system.
Here is the leaning pot I found that will solder
to the mother board and poke through the instrument panel.
Also the switches I plan to use.
Another option is to let the builder choose the switches
and pots and mount them remotely from the mother board.
The downside is more skilled labor required to wire them
to the mother board. There will be at least one pot and
one switch for every two injectors. That way the mixture
can be adjusted separately for each rotor based on the EGT.
What do you all think?
I am also looking for somebody
building an EFI engine that would like to try this
prototype system on the ground for free. Let me know
where so I can show up when you are ready to test.
You will need to buy a wide band mixture monitor.
Paul Lamar
Paul,
I vote for remote mount. Planes are so different.
Joe Berki
Limo EZ
Hi Paul
IMHO, Both-ideas are good. On the mother board neat and allows tuning
injectors and allows the ability to get around injector and faults etc.
A separate remote mixture is good to. But not four for a two rotor
or six
for a triple.
I would go for both, ire as originally suggested with separate pots
on the
mother board, for individual rotor tuning and trouble shooting
getting round
problems etc. A separate remote pot, for overall mixture.
I hope I explained it and if that's what was meant already; apologies in
advance.
Come to think of it. I would mount the motherboard flat so if at the
top of
the panel I could lift an access panel and change control circuit on the
fly. Or mount it so the changeable 555 circuits were at the bottom
of the
panel all the switches and pots 90 degrees to the circuits like the
alternative injector connecters.
And the remote mixture pot mounted on the throttle lever sort of
instead of
the usual knob. So open and close the throttle and adjust the
mixture with
my thumb. (OK that might not work in practice, so I could change it to
operate as a normal mixture lever.)
Hope this helps.
Clive C
Paul I am planing on using 555 system have a question I am thinking
of using stock engine turbo intake manifold with lots of external
cleaning it only has 2 injectors will this work I will be running a
stock turbo on 13B if I can figure waste gate controller or best place
to find such info??
Keith Menard will be setting engine on test
stand soon air frame 3/4 complete
There should be two injectors in the center housing and two more in the original
intake manifold. If you are making your own intake manifold I would add a couple
of injectors. Be real careful with the 555 system as the turbo engine
is sensitive to leaning at high power. You probably want to remove the waste gate
valve and run the waste gate wide open. Also have someone trim the turbine down.
There are turbo outfits that will do that for you. Tell them your running it
in a boat at a high altitude lake at constant boost and you heard that
it will over rev and destroy itself. (True) At least five stock turbo's
have been destroyed so far by using them in aircraft.
http://www.bnrturbos.com/2ndGen.htm
The turbine part has way too much HP to run at constant speed constant
boost. Trimming the turbine down does two things. It reduces the mass of
the blades so they are less likely to fly off or come apart at high RPM
and the HP of the turbine is reduced.
I would do that after you get it running. Get a turbo tach kit from
Garret and run the engine on the ground. Measure the turbo RPM at full
power. If it goes over 80,000 RPM cut it down before you fly it.
Dave Leonard on here might chime in as he has been flying one for a few years.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.