Subject: Pressure taps are in
From: Rotary Engine
Date: 7/4/2009, 9:42 AM
To: AAA Put this in the To box

Paul,

What is Tracy's manifold problem?

How does it solve the problem?

I missed an earlier discussion, so pointers appreciated!

Thanks,

Tom



Here is the original thread on the subject with some snips...
to keep it focused. The pressure measurement was all over the chart
and Tracy was sampling it at only one point at an unknown time.
Sampling the pressure in and at the start of the compression chamber
solved the problem.

Also see http://www.rotaryeng.net/fund-of-intake.html
to view some of the pressure variations we were seeing in the intake
manifold.

Paul Lamar

--------------------------------------------------------------
-------- Original Message --------
Subject: Tuned intake manifold pressure  test.
Date: Sun, 10 May 2009 18:51:25 -0700
From: Rotary Engine <rotaryeng@earthlink.net>
To: AAA Put this in the To box <rotaryeng@earthlink.net>

The five volt on board power supply this thing comes with
makes it real easy to wire up.

Here is the results of the first pressure sensor test. I
used
a hand vac pump to reduce the pressure from sea level
to about 26 to 27 inches of Hg vac.
The numbers at the bottom of the chart are the sample
numbers at
1000 samples per second. Data rez is to the nearest 1/1000
of a volt.
Sea level is 1.8 something while full scale is close to 4.1
volts.

This thing is real easy to use.

-----------------------------------------------------

Well I got it all together. I used another analog
channel to serve as a TDC mark using the Mazda 2nd gen
RX7 Crank Angle Sensor.

I took the gear off the CAS so I could drive it with
a rubber band belt from a drill motor. I got it up
to 2000 RPM.

    The output of the 2nd gen CAS looks just like an
RX8 CAS or a anti lock brake system sensor. They all use
the same
principle.

I used an opto isolator for the trigger signal as I did not
want to risk grounding problems. The positive part of the
trigger
pulse turns on the LED which turns on the photo transistor
which inverts
the pulse. That is why it goes negative.

------------------------------------------------
This last plot is only .4 seconds worth of data taken at 2
milli seconds
apart. Truly amazing. A super high speed camera shot of
what is going
on in the intake system. The blue and red lines are the
pressure sensors not connected
to anything. The yellow line is the trigger from the 2nd
gen
crank angle sensor. The yellow pulse happens at E-shaft top
dead center.
You can see the drill motor accelerating on the left of the
chart.
It peaked out at 2000 RPM.

I can hardly wait to test Mark's P-port engine. 1800
RPM to 6600 RPM.
To my knowledge this is the only time, since the book,
Scientific Design of Exhaust
and Intake systems was published in 1962, this level of
data was available.
In those days they used an ingenious rotary valve driven by
the crankshaft
to measure the pressure data from an intake or exhaust
manifold using
18 U tube manometers.

We will have data over a wide range of RPM's which was
not available in the
book. Mazda published just a snap  shot of one cycle at one
RPM of a p-port
engine probably using an O-scope.

Paul Lamar


snips..

I just got back from Denver testing Mark's p-port engine with the data ack system.
It ran really bad when we were sampling the pressure data from the intake
tubes for Tracy's EFI system. Once we installed the pressure taps in the rotor housing
through the apex seal oil injection ports it ran much much better and would idle
down to 1000 RPM or about 350 prop RPM. Not as good as a RX8 p-port engine but more
than well enough for an aircraft engine.

Larry, we need to make some of these apex oil port screw in pressure taps. I'll do a dwg.
The .070 inch diameter hole made all the difference IMHO.
Some pressure plots shortly. We got almost a gigabyte of wave form
data at a wide range of RPM's.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2008 All world wide rights reserved.