Steve Beckham came up with this after market water pump
cartridge. Saves 2 or 3 pounds.
Paul Lamar
Paul,
Where did he get it? The web site on the box doesn't have any
retail suppliers listed.
Blake
Yes I am trying to find out. It is a big company and I sent
them email. I will hit them up for sponsorship money for
the racer in exchange for a decal on the RV3 :)
Paul Lamar
That's an early RX7 Water Pump.
gmb 145-1180 is the part number.
Description:
Description: Standard Pump / Water Pump;Eng Code 12A, 13B ; OE# 8872-15-010B;
Years: 1984-1985;Qty Per Vehicle:1;
Google does list multiple suppliers (I just haven't dealt with any of
them. Does anyone know of a Mazda Specific online dealer (i.e. all my
Honda parts I go to Majestic Honda... OEM at 25% discount)
Tom
http://www.rotaryeng.net/part.html
http://www.mearsmotors.com/
Mention the rotary engine newsletter to the parts manager.
Bob Mears is building a 3 rotor scale spitfire.
Paul Lamar
Steve
Two questions. What is the maximum water flow on the unit as mounted on
the engine with its accompanying flow restrictions? Is the rear of
the water pump a simple flat plate with inlets and outlets installed?
I see you mounted it down in the southeast corner of the engine
accessory side. Smart.
Thanks
Doug in Japan.
Stock pump in stock location. Only the output port has been modified.
The weird motor mount is fooling you :) Only the cartridge is different.
Same water flow as stock.
Paul Lamar
Paul,
If it is the same flow as stock why change it? Convient outlet
positions? Jim at Racing Beat told me the stock pump would not flow over
40 gallons a minute and any engine producing 200 Hp continuously is
going to need well over 45 gallons a minute. Granted most guys are not
going to flying at that power level.
BTW. an accurate flow test has to be done with the plumbing connecting
the pump to an actual motor housing and heat exchangers. A bench test
with PVC pipe and a restrictor valve to create system back pressure
does not accurately simulate the countless eddies and restrictions in
the block.
Doug in Japan
It saves 2 to 3 pounds Doug. Aluminum cartridge instead
of cast iron cartridge.
I don't think you are getting the pictures I am attaching.
Are you using the Mac? Do you have your browsers set to automatically
display attached files?
I sent you a flow curve carefully measured by an aerospace engineer
friend of Al Gietzen on a dyno engine where the flow was 50 GPM at 6500 RPM
and still rising strongly. No thermostat. Here it is again along with
some other stuff.
On the other hand there are people around that have ignorantly reduced
the hose size to 1/4 the area of the stock hose and their engines
are not falling out of the sky. In fact I know some people that
have used electric water pumps that have 20% or less of the flow capacity
of the stock pumps and still the engine was not over heating.
I think Jim is wrong and I think he never embedded a thermal couple
down near the combustion chamber just along side the spark plug.
Look in my book on page 84. There is a picture on where to
put the thermal couple if you don't get the attached pictures.
This is the hottest part of the rotor housing. Most of the mis info
floating around prior to people actually instrumenting the engine
was hearsay or urban myth.
Early coking on the rotor housing wear surface IMHO was caused by
using natural oil made 10 miles down below the surface of the earth
formed from rock and water :) Not synthetic 2 cycle oil. Another
possibility was the apex seal spring temper went away and the apex
seal was floating or stuck in that area of the rotor housing. Francisco
Ianettie told me to use a very stiff springs indeed with his ceramic apex
seals if I were going to run the engine at 11,000 RPM. The apex seals in
the p-exhaust port engines run 500 F and that can weaken some springs.
There is a lot of after market junk apex seal kits on the market.
If in doubt people need to do an apex seal spring test were a weight is hung
off the end of the spring while it is in a cooking oven set to 600 F and
while the deflection is measured.
Mark Steitle has done the rotor housing thermal couple trick and he is
reporting temperatures several hundred degrees F below an air cooled
piston engines CHT's.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.