Subject: New front cover with motor mounts.
From: Rotary Engine
Date: 7/14/2009, 5:30 PM
To: AAA Put this in the To box


Phillip Groelz is building a cast aluminum front cover incorporating
Lycoming motor mounts much like the Mistral version.

Add some bosses on there Phillipe to mount my ignition
and fuel injection crank angle sensors :)

I talked to Steve Roth who was piloting when the
Mistral Piper Arrow crashed and he said the front cover did not break but
the motor mount was bent. Always good sign. Means the front cover can take
it.

Here are some pictures of the wood patterns and the Mistral version for
comparison. I like the idea that Phillip is using the stock Mazda water
pump
cartridge.

Paul Lamar
------------------------------------
Paul, and Phillip!
Sign me up for a couple (or 3) of those castings! Try and make sure they
fit
all versions of the 13B and 20B's, the 20B larger water pump, have acc pads
(cs prop pulley driven pump), etc! (I have mostly 13B REW and 20B
engines-the AT engines have a different bolt/starter layout, as does all
the
20B's as they were ALL AT only). In any case.
I suspect that this mount is the typical "dynafocal" Lycoming style used on
the Lyc O and IO360's like in some of the Piper Arrows If so, I have this
MM hanging from my hangar ceiling. I was waiting for this to happen.....and
didn't want to deal with Mistral......
Any idea on a price and when

Marc Wiese

Sign me up as well. I'm at least a year behind with doing the same thing.
Had thought of purchasing a complete Mistral engine just for the chance
to measure and CNC that front plate. If it's engineered to handle the
loads of up to and including a 4 rotor you should have no problems
getting customers. Price and timeline would be great.
Greg Fleming
London, Ontario, Canada


Sign me up too if you're taking orders! :-)I have a 20B and would
really like to use this type of mount with my Velocity SE-RG. Any
idea of the weight yet Will the longer tension bolts of the 20B
handle the additional weight thats cantilevered out This would be
a nice piece of work to use with our engines!
Best wishes,

John Bell

Paul, I have been using RX7 and RX8 side housings to measure bolt locations
and water and oil passage interfaces. It looks to me that the tension bolts
thread into the front side housing and do not pass through it to the front
accessory case casting.It looks like the patterns shown will gain some
support from the oil pan attach bolts and water pump studs, however these are
small fasteners and while the oil pan itself appears plenty stiff, the bolt
hole clearance would limit support to the friction component of the pan and
gasket to the front cover. I would suggest looking at some through bolt
bosses that would allow attachment of 1/4" plate brackets back to the core
engine castings. The mounting front cover mounting idea should advance
rotary use as Lycoming mounts are available for most anything, and the motor
mount worries builders more than the induction system which you have already
taken the pain out of. How does the center of gravity of the
rotary/redrive/prop compare with the Lycoming engine an prop assuming the
cooling system is under the engine
george grimes

The center of gravity will be well forward of the Lycoming. I was concerned
with the same thing and that is why I checked with Steve Roth of Mistral.

If it survives a crash it is probably strong enough.

The two hollow dowel pins would help locate the motor-mount/front-cover.

The oil pan flange will help out as you mentioned.

Seems to me is the most highly stressed part of the new front cover is the
upper right corner with few six mm bolts in that location. Mistral has
added at least one new 6 mm screw in that area. High strength bolts are used.

Paul Lamar

Paul,
It appears that Mistral has committed to a front motor mount for a bed
style mount on the 3 rotor.
You may have seen newer layouts so I'm asking here. All the 3 rotor displays
used a mount attached to the bell housing. The mounting pad for that
was almost in the same place as the Shirtz mount designs on the 13B
mounts you have been doing. It doesn't appear that Mistral wants to
mount the 3 rotor off the front/rear plate. It seemed smarter to do
a P51 style mount for the 20B. Your thoughts
Bill Jepson

Here are some pictures I took at Aero in April 2009. Still the Lycoming
cantilever mount.

I am biased as I came up with the mount under the engine/GB/Prop combo CG :)
for the rotary. Well not me. Jim Griswald used it on the Questair Venture.
The Lycoming mount for a 3 rotor is a risk.

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.