Subject: New front cover with motor mounts.
From: Rotary Engine
Date: 7/15/2009, 7:25 PM
To: AAA Put this in the To box



 Phillip Groelz is building a cast aluminum front cover incorporating
 Lycoming motor mounts much like the Mistral version.

 Add some bosses on there Phillipe to mount my ignition
 and fuel injection crank angle sensors :)

 I talked to Steve Roth who was piloting when the
 Mistral Piper Arrow crashed and he said the front cover did not break but
 the motor mount was bent. Always good sign. Means the front cover can take
 it.

 Here are some pictures of the wood patterns and the Mistral version for
 comparison. I like the idea that Phillip is using the stock Mazda water
 pump
 cartridge.

 Paul Lamar
 ------------------------------------
 Paul, and Phillip!
 Sign me up for a couple (or 3) of those castings! Try and make sure they
 fit
 all versions of the 13B and 20B's, the 20B larger water pump, have acc
pads
 (cs prop pulley driven pump), etc! (I have mostly 13B REW and 20B
 engines-the AT engines have a different bolt/starter layout, as does all
 the
 20B's as they were ALL AT only). In any case.
 I suspect that this mount is the typical "dynafocal" Lycoming style used
on
 the Lyc O and IO360's like in some of the Piper Arrows If so, I have this
 MM hanging from my hangar ceiling. I was waiting for this to
happen.....and
 didn't want to deal with Mistral......
 Any idea on a price and when

 Marc Wiese

 Sign me up as well. I'm at least a year behind with doing the same thing.
 Had thought of purchasing a complete Mistral engine just for the chance
 to measure and CNC that front plate. If it's engineered to handle the
 loads of up to and including a 4 rotor you should have no problems
 getting customers. Price and timeline would be great.
 Greg Fleming
 London, Ontario, Canada



 Sign me up too if you're taking orders! :-)I have a 20B and would
 really like to use this type of mount with my Velocity SE-RG. Any
 idea of the weight yet Will the longer tension bolts of the 20B
 handle the additional weight thats cantilevered out This would be
 a nice piece of work to use with our engines!
 Best wishes,

 John Bell


Paul, I have been using RX7 and RX8 side housings to measure bolt locations
and water and oil passage interfaces. It looks to me that the tension bolts
thread into the front side housing and do not pass through it to the front
accessory case casting.It looks like the patterns shown will gain some
support from the oil pan attach bolts and water pump studs, however these
are small fasteners and  while the oil pan itself appears plenty stiff, the
bolt hole clearance would limit support to the friction component of the pan
and gasket to the front cover. I would suggest looking at  some through bolt
bosses that would allow attachment of  1/4" plate brackets back to the core
engine castings. The mounting front cover mounting idea should advance
rotary use as Lycoming mounts are available for most anything, and the motor
mount worries builders more than the induction system which you have already
taken the pain out of. How does the center of gravity of the
rotary/redrive/prop  compare with the Lycoming engine an prop assuming the
cooling system is under the engine? george grimes

The center of gravity will be well forward of the Lycoming. I was concerned
with the same thing and that is why I checked with Steve Roth of Mistral.

If it survives a crash it is probably strong enough.

The two hollow dowel pins would help locate the motor-mount/front-cover.

The oil pan flange will help out as you mentioned.

Seems to me is the most highly stressed part of the new front cover is the
upper right corner with few six mm bolts in that location. Mistral has added
at least one new 6 mm screw in that area. High strength bolts are used.

Paul Lamar

Is this cover meant to fit the larger 20B (and 13B REW) oil pump
configurations? Those engines have uprated oil pumps.
Marc Wiese


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.