Subject: Hall effect trigger for 555 EFI and ign.
From: Rotary Engine
Date: 7/16/2009, 4:59 AM
To: AAA Put this in the To box


I have decided to do away with the ABS and crank angle type
magnetic inductive sensors as too expensive and too big. I would have
trouble
clearing the water pumps. Klaus has been using hall effect sensors
for years so I am going to copy him. They are cheap at less than
2 bucks each and we need ten. It will only require one small rotating
magnet to trigger the ten sensors. The sensors can be placed
much closer together so the diameter of the trigger system
can be reduced and fit below the water pump.

Klaus's system fits on the prop shaft so it must be much
larger than necessary compared to our e-shaft pulley.

Here are some graphics on the ABS sensor type and the hall data
sheets.

I have lots of experience using optical sensors. They work well and
are
cheap and easy to use but they are way too prone to dust and grease.

----------------------------------------------------------


This is the one I am going to try. I ordered
a couple from Digikey. The price went up to $6  each but
that beats $16 each for ABS sensor since we need ten.
If it works and I buy more than the price will go down.
We don't have a lot of choice in the matter as the trigger
mechanism will be limited in diameter due to the
proximity of the water pump. These things are tiny so
the circuit board will be small and light weight.

If anybody has any experience using hall effects sensors I would like
to hear about it. Klaus has been using them for quite awhile
so I will also talk to him when I get a chance.


I am worried about the end play on the e-shaft but the Lycoming engine
also has end play. I'll check all that out on the bench.

Paul Lamar



Paul,
The Lycomings end play might be a problem, but I doubt that
the Mazda e-shaft end play would be a problem. The O-200
rebuild video I watched had be chuckling because they
said up to .10 inches was "acceptable"! I don't think my
20B has more than .020 inches if that. Too bad motorcycle
parts are so expensive,several Kawasakis use them for
engine timing. They are small too because they have to
fit inside a motorcycle case.
Bill Jepson


 Seems like the end play is only critical with one orientation of the
 sensor..  On my O-200 with an early LSE ignition, the trigger bolt is
 oriented radially and the sensors are mounted outside of that.  End
 play has essentially no effect because the sensor's response are is
 relatively large in this axis.  If there were significant run out,
 there might be a problem..


 Matt-

 Sounds like you may have one of Klaus's earlier inductive trigger
systems.
 Are there any rotating magnets?
 Can you take a pictures and send it to me?

 Paul Lamar





No magnets.

Regardless, it seems that the triggering device and the sensor could
be oriented so that a small amount of end play won't cause problems.

Klaus' hall effect sensors are mounted where the magnetos are normally
installed.  I believe they require the use of a mag gear to make them
work (on Continental or Lycoming)..


Matt-



The problem is we need a round flat circuit board to locate the
sensors.
This board will face the front e-shaft pulley with the magnet
mounted on it. Sort of a face to face arrangement. Therefor the
magnet could change it's distance to the sensor with e-shaft end play
so the flux could change as well. Not a good thing.

I'll see when I set it up on the bench.

Paul Lamar


Paul,
No Hall sensors either:) Time to enter the 21st century and go
optical.

Design:
The PSRU side of the engine has more space advantages. Attach a flat
target ring of  optical material or even a white strip with bar code
lines to the outer perimeter on the back of the flex plate. Dust
isolation is a no brainer. Look at your CD drive in front of you. It
still works fine on your dusty hot desk.  You may  have to ask Robin
to
show you what a vacuum cleaner wane looks like as it is the brush like
hairs that surround the inlet that I am referring to:)  A bowl like
cover mounts to the engine block and on its perimeter is  brush like
seal that wipes the outer edge of the target ring and creates a dust
seal. Using clean room design techniques, slightly pressurize the
chamber with clean air so engine heat escapes outwards along with dust
near the seal.

Operation:
 Every time a line passes by (or digital water mark is read) a coil is
fired. Have as  many tracks and sensors as there are rotors, spacing
the
sensors inwards and outwards.  If  reading digital info then one laser
and one track is  fine but I know you don't like that idea.  However
one you might enjoy is  to install another  optical sensor within the
cover  that shines through a plastic lens hole in the flex plate  and
reads part of a bar code  it sees on the back of the PSRU drive plate,
once per rpm.  Yes that space can be kept clean as well as it doesn't
change in volume very much. The mark positions and hence their
equivalent numeric info will change vis-a-vis  the  drive plate
because
there is rubber in between them. The lens is important.  At increasing
rpms  more and more of the code can be seen, or conversely be hidden.
Info output is digital but easy to transform into a torque number.
Just
total the  series of numbers. For best resolution this sensor and
target
should be installed as far out on the sensor ring as possible. This
insures the maximum movement between the two plates. For bar codes we
need a few millimeters.  For optical discs 1/100 of that. Yes it will
have to be calibrated and yes it might change as the rubber absorbers
age.  Recalibration is as easy as hanging weights on the prop at a
known
distance and multiplying it times the gear ratio.


Doug in Japan

Been there and done that Doug. Too hard to get to and maintain.
It is also a very hot place so I would have trouble with heat
affecting the electronics.

I like the Hall Effect as it is is tried and true on Klaus's
airplanes. I am going to leverage off his experience. No point
in reinventing the wheel.

Paul Lamar


Paul -

I did a quick search and came up with a sensor that might work for you:

NXP KMI15/4 Rotational speed sensor
http://www.nxp.com/acrobat_download/datasheets/KMI15_4_4.pdf

It puts out a digital signal that's already cleaned up.  I'll try to
order some samples.  (I'm sure others can find something better.)

This part DOES NOT require a magnet, just something ferrous. (Like a
single bolt at the perimeter.)  About $4 each at Digikey.

It looks good for 25KHz tooth rate, WAY beyond your intended use.
That's almost fast enough to sense the flywheel starter teeth!  It
could certainly count turbo blades.

I hope this sensor is helpful.

-Vince Orton


P.S. QUESTION: How many starter teeth ARE in the 13B flywheel?

MATH:
25Khz * 60sec/min
------------------- = 187.5 flywheel teeth (max)
   8,000 RPM

25Khz * 60sec/min
------------------- = 150 flywheel teeth (max)
   10,000 RPM

Very interesting. Looks like a miniature version of the current ABS and crank
angle sensors sort of. Looks much more stable with temperature than
the Hall effect.

I'll have to get one and try it out.
Any idea of the cost?

I don't know on the number of teeth on the flywheel. All flywheels
are up at the hangar.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.