Subject: Low cost Slide throttle kit?
From: Rotary Engine
Date: 7/24/2009, 10:44 AM
To: AAA Put this in the To box


 I could use oneKeith Menard How many would be interested
in a low cost
 Teflon slide throttle kit?
 The side plates can be NC punched out relatively cheaply
much like
 an RV
 airplane is pre punched. You can make the Teflon part on a
drill
 press and
 hole saw.

 Paul Lamar



 Definitely count me in for one of those. Will it all fit
in a $5
 box? ;-)
 C. Smith

 Don't know what it will cost as it won't fit a flat rate
box.
 I'll need to weigh it. My guess is metal part will be less
than
 2 pounds. It is also about 15 inches long.


 Paul Lamar


 Count me in for one too, Paul.

 Barry Doublestein
 Atlanta Glasair SII FT
 N59BD


 Hi Paul

 I do have a question,did someone try this device in
flight?
 did someone face with fuel leaks with this slide throttle
kit
 before??/
 Jean Prudhomme


 Not yet but it is going to fly any minute now.

 Slide throttle have been used on Mazda racing engines for
30 years.

 Yes. We had slide throttle leaks on the original dyno
version but
 we fixed
 that with 1/64th (.015) thick gasket material. Now all raw
excess fuel
 is captured and runs into the engine.

 The engine is running fine and the slide throttle is
working slick
 as snot according to Mark Suspinski :)

 Paul Lamar



 If you run your P Port all over the engine and install
 the slide on the sparplug site and injectors location
 do you think it can be a difference on performance.


 Jean Prudhomme


 Not recommended. It hurts the running of the engine at
lower
 RPMs. You want to keep the throttle as close to the rotor
 housing as possible. Steve Beckham on here put the
throttles
 just inside the rotor housings. At part throttle the
runners
 store exhaust gas due to valve overlap and make the
engine
 miss. This was discovered almost as soon as people
started
 building Wankels. The NSU Wankel spider engine had the
throttle
 in the p-port rotor housing way back in the middle
1960's.


 Paul Lamar



  As Paul said, the prototype slide throttle is
working hunky-dorey on my
  pport.Even at max static rpm, there is no hesitation
or binding
 on the
  slide.Since my model left the "Lamar International"
  factory, there were a few improvements to the design
which Paul
 attached in
  an earlier message already (so don't be surprised if
the pic of
 mine from
  the first response doesn't match the drawings).

  The one important bit is to use the proper gasketing
material (Paul
 leap in
  here & say what it is).During start (we prime 4
- 6 pushes on the ec2
  before start), fuel does tend to collect in the
slide & if the gasket
  material is wrong it will end up leaking out onto
the exhaust (not
 a good
  thing).This excess fuel in the slide causes the
engine to run
 rich for
  the
  first couple of seconds.After the engine gets
running for a bit &
 sucks
  it
  all out it all settles down nicely.

  We're a couple weeks away from first flight --
mostly due to me
 taking the
  kids to the House of Mouse next week.I fighting a
few sensor
 issues (sure
  would be nice to know how much fuel is in the tank)
before calling
 the DAR.
  The throttle has worked flawlessly during our high
speed taxis.

  Mark (Rocky Mtn High)
  *BTW - the only issue I have with the slide throttle
in it's
  current incarnation is that it's a bit tough to
"tune" the
  position of the slide vs position of the throttle
handle.This
  is due to the intake tubes being curved, so you
can't visually
  see the exact position of the slide for any given
throttle
  position. In my case, it is possible (due to the
position of
  the holes in the slide itself) to go a bit beyond
WOT - which
  starts closing off the opening again.Thus I have to
hold it all
  together in position without the cover plate
attached, adjust
  the connection so throttle handle WOT is when the
slide is
  exactly at WOT, and then bolt it all together.Not an
enormous
  problem by any means, just a bit more work.

 Also, be prepared for a bit of creative routing for theh
  throttle cable.On some ships, getting from a
centrally mounted
  throttle handle over the port side of the engine can
be a bit
  of work.  Mark Supinski, You've done a very
nice install.Let
  us know how the inspection and first flight goes,
and how the
  slide throttle works in actual flight conditions.


 Mark S.
 Austin (Rocky Mountain Low)

 BTW - Did you get around to re-doing that fuel rail
mount?


 Mark Supinski,

 Get one of those cheap Harbor Freight bore scopes and
stuff it down
 the intake tube. It will also be useful for inspecting
your muffler.
 The kit will have the correct dimensions so when the slide
is fully
 open the holes in the slide will align with the tube
openings.
 The slide throttle you have is a prototype. I am sorry it
was not
 correctly made.

 Paul Lamar


 I could use one Keith Menard.


Paul,

Please put me down for one.

Joe Graham

You read my mind. I was just working on the final drawing.
I talked to my pilot buddy down in Torrance yesterday that
is going
to make the parts. He builds a lot of parts for Boeing and
Airbus.
His tig welder is an artist as he tigs welds aluminum 8
hours
a day day in and day out.

He wants to build the whole thing including tig welding
them up.

But that is a costly thing for me to do as the tubing
bends
alone are about $30 each. I am sure he would not do less
than
ten at a time.

If ten people come up with half the cost I might be able
to
swing it. Or perhaps everybody sends me bent tubing.

Shop around and see if you can find tubing bends cheaper
than Burns Stainless is charging. Two inch OD .065 wall 180
degree
bend. http://www.burnsstainless.com/

Here are some pictures  of his shop.

He also just acquired a large Fadal NC mill so he will do
the
spacer as well.

Paul Lamar



Why don't you take deposits, of say $50 up front, and balance due
when a run of kits is completed and you have the full costs figured out?
I'm going to want a set of the aluminum intake rings too. what were
they, ten bucks each? ship 'em all together when the slides are ready.
C. Smith

That is another possibility. The rings were $5 as I recall.
I am going ahead with the slide throttle kits less the tubing
bends and Teflon anyway.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.