Subject: Low cost Slide throttle kit? Prices
From: Rotary Engine
Date: 7/25/2009, 9:16 AM
To: AAA Put this in the To box

You read my mind. I was just working on the final drawing.
I talked to my pilot buddy down in Torrance yesterday that
is going
to make the parts. He builds a lot of parts for Boeing and
Airbus.
His tig welder is an artist as he tigs welds aluminum 8
hours
a day day in and day out.

He wants to build the whole thing including tig welding
them up.

But that is a costly thing for me to do as the tubing
bends
alone are about $30 each. I am sure he would not do less
than
ten at a time.

If ten people come up with half the cost I might be able
to
swing it. Or perhaps everybody sends me bent tubing.

Shop around and see if you can find tubing bends cheaper
than Burns Stainless is charging. Two inch OD .065 wall 180
degree
bend. http://www.burnsstainless.com/

Here are some pictures of his shop.

He also just acquired a large Fadal NC mill so he will do
the
spacer as well.

Paul Lamar
Why don't you take deposits, of say $50 up front, and balance due when a
run of kits is completed and you have the full costs figured out?
I'm going to want a set of the aluminum intake rings too. what were
they, ten bucks each? ship 'em all together when the slides are ready.
C. Smith

That is another possibility. The rings were $5 as I recall.
I am going ahead with the slide throttle kits less the tubing bends and
Teflon anyway.

Paul Lamar

I think a $50 deposit up front is reasonable Paul. What ever you guys
decide let me know and I'll send the $$.

Mike C.

Paul,
Me too.
Gene Sandburg

Paul,

I am still in. Just let me know how much.

Regards,
Gordon

-
OK I have come up with a compromise solution here.
Since there are several configuration for mounting
the slide throttle and intake runners it is not a good idea
to weld the 180 degree tubes to the outer slide cover.

What we can do without accepting a bunch of money in advance
is weld short tubes to both inner and outer covers and everybody
can do their own thing with rubber couplings, hose clamps and
180 degree bends. If you get something you like you can
then butt weld the 180 degree bends to the short tubes if you wish.

In certain airplanes, like canards, you may be able
to run straight tubes. Other airplanes you can go up and over
the engine or tilt them over along side the engine if you
have a side by side airplane. Lots of flexibility in
this approach.

What do all you slide throttle buyers thing about this idea?

Paul Lamar


I - Keith Menard  need the slide kit and curved intake tubes and
injector blocks I have 4 13B engines to play with to put in my RV7
70% comp Please tell me when and where to send up front deposit
I will make Oshkosh this year to much work
I am in process of building test stand to mount engine for test run??

Keith Menard

We will not be selling the intake tubes. Get them direct from
Burnes Stainless in aluminum. 2 inch OD and .065 wall 180 degree
bends. http://www.burnsstainless.com/

The rest of the stuff except for the slide throttle kit
we will ship Monday or Tuesday. I'll let everybody know the price
of the slide throttle kit when I am ready to ship.


Sealing plates are $10 each two per 2R engine.
Pressure taps are $15 each two per 2R engine.
Bell mouths are $5 each two per 2R engine.
Dual skinny Injector blocks are $15 each two per 2R engine.
Plus $5 flat rate postage and boxing anywhere in the US.

Send cash only to:
830 East Santa Maria St.
Suite 303
Santa Paula CA
93060

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.