Subject: : Low cost Slide throttle kit?
From: Rotary Engine
Date: 7/27/2009, 2:16 AM
To: AAA Put this in the To box


  You read my mind. I was just working on the final drawing.
  I talked to my pilot buddy down in Torrance yesterday that
  is going
  to make the parts. He builds a lot of parts for Boeing and
  Airbus.
  His tig welder is an artist as he tigs welds aluminum 8
  hours
  a day day in and day out.

  He wants to build the whole thing including tig welding
  them up.

  But that is a costly thing for me to do as the tubing
  bends
  alone are about $30 each. I am sure he would not do less
  than
  ten at a time.

  If ten people come up with half the cost I might be able
  to
  swing it. Or perhaps everybody sends me bent tubing.

  Shop around and see if you can find tubing bends cheaper
  than Burns Stainless is charging. Two inch OD .065 wall 180
  degree
  bend. http://www.burnsstainless.com/

  Here are some picturesof his shop.


  He also just acquired a large Fadal NC mill so he will do
  the
  spacer as well.

  Paul Lamar
  Why don't you take deposits, of say $50 up front, and balance due when a
   run of kits is completed and you have the full costs figured out?
   I'm going to want a set of the aluminum intake rings too. what were
   they, ten bucks each? ship 'em all together when the slides are ready.
   C. Smith

   That is another possibility. The rings were $5 as I recall.
   I am going ahead with the slide throttle kits less the tubing bends and
   Teflon anyway.

   Paul Lamar

   I think a $50 deposit up front is reasonable Paul.What ever you guys
   decide let me know and I'll send the $$.

   Mike C.

  Paul,
  Me too.
  Gene Sandburg

   Paul,

   I am still in.Just let me know how much.

   Regards,
   Gordon

   -
   OK I have come up with a compromise solution here.
   Since there are several configuration for mounting the slide throttle and
   intake runners it is not a good idea to weld the 180 degree tubes to the
   outer slide cover.

   What we can do without accepting a bunch of money in advance is weld
short
   tubes to both inner and outer covers and everybody can do their own thing
   with rubber couplings, hose clamps and 180 degree bends. If you get
   something you like you can then butt weld the 180 degree bends to the
  short
   tubes if you wish.

   In certain airplanes, like canards, you may be able to run straight
tubes.
   Other airplanes you can go up and over the engine or tilt them over along
   side the engine if you have a side by side airplane. Lots of flexibility
  in
   this approach.

   What do all you slide throttle buyers thing about this idea?

   Paul Lamar

   That will do nicely!
   C. Smith

  I would be interested in one of your Teflon slide body kits also.

  Capt. Will


Paul,

If I had my rathers, I would just go with the configuration you are showing
for the RV-7A with ram air box. Find out what the most popular configuration
is and build to that.  Those who wish otherwise can cut and reweld
accordingly.

Thanks,
Gordon

I think you should stick with the short tubes, and then people can add on
from there.
C. Smith

I talked to my buddy that is going to weld on the short tubes.
Here are some pictures of his work.


Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.