Subject: Mazda bell housing pssru
From: Rotary Engine
Date: 8/5/2009, 6:49 PM
To: AAA Put this in the To box


Jean P,

I know you are interested in this as
you wanted Bulents email address.

Here is some stuff I have on it.
If you need more help let me know.
Tracy's box can be adapted to just about any stock light weightdie cast
Mazda bell housing.

Paul Lamar

I'm curious about this as well. Is there a mechanical, or monetary
advantage
to this, over Tracy cook design? Can you buy a partial Tracycook unit
 that
costs less? I do have a transmission laying around.
C. Smith

The advantage is mostly cosmetic. I am not sure Tracy will give
you much off if any for his adapter plate and spacers.

Paul Lamar
Paul, thanks for posing the pictures. As you might recall I adoing cad
 work on new side hosings to work with tracy crook's redrive and am
 incorporating a taller flange with added bolt holes. It appearsfrom the
 pctures that the stock bellhousings areover 5" tall which wouldbe more
 material (weight) than the spacers for the redrive.
I like the availability
 of two starter motor locations on tracy's adapter plate and considered
using
 two stock starters on the six rotor by machining tha alternateloation from
 the drawings I got off the newsletter. With the taller flange Ihope to
 make
 a more close coupled attachment to the plate. I don't seem tohave the
 height of tracy's spacers and have been using 3" on the drawings. I am now
 compiling the solid models and was wonderingif someone would take a dial
 caliper to the spacers that would be used on an RX8 engine andpost it on
 the newsleter.
george grimes

The stock bell housing are super thin high pressure die castings
 .125 inch in some places so they are about the same weight asTracy's 3
inch high 1/2 inch thick plate set up.

Paul Lamar

Paul, thanks for the quick response. I plan on using Tracy's 1/2" plate so
the extended flange will be heavier than the spacers in the drive kit.
Another incentive to use magnesium alloy in place of the356 T6 aluminum
for the casting. The solid model buildups are progressing although the
pattern draft is occasionally a struggle. I joined bunches of features
together in layer to make them easier to assemble and ge"inconsistant face
edge relationships" as an error and haven't yet figured out whatto avoid
doing this. All parts attempted are working out, just a little extra time
to
finish. The front mount for a "P-port" is done and I hope to get the
aluminum section of the front housing done today.

george grimes

You would be better off with Solid works or Rhino. Draft features
are built into Solid Works.

Paul Lamar

I hope to borrow time on s Solidworks 2008 platform in a fewweeks.In
 order to reduce the time required on someone's business computer which has
a
 single use license I am trying to get all I can out of my current software
first.

I don't want to wear out my welcome ove there and it is 6 hours down
 the road and requires motel rental. I still have rhino version 1and may
try
 that in a few days since it will open my dwg.files if saved under
 autocad14 DFX.
george grimes

Solid Works is not easy to learn. It takes years sometimes to become
 really proficient. I would stick with Rhino ver 1 and get up
 to speed on that. I can help you there. 3D is major leap forward.
Paul Lamar

Don't forget you've got experienced SW users [6yrs] on here and willing to
help
if the need arises :)

Jarrett

I am hoping to send the solid models to Paul  in dxf format in about two
weeks. This will be a center housing cooling system engine with  periphial
port intake and either side port or periphial port exhaust, and also the
interengine side housings that allow 13B e-shafts and rotor housings to be
joined into four rotor and six rotor engines. If the lightning outside would
let up so I can start up my computer  I would do the center cooling housing
today. the cross sections are complete and need turned into a solid model.


The eight port side intake system  is a work in progress,just needing to do
the final drawing, and the
slide throttle for the 24 total ports is just notes at present. There are
blocks similar to the p-port blocks on the side housings to direct mount the
slide throttle backplate with oring sealing.The front mount iron will have
to be different for the side port due to the  intake ports pretty much
running through the top right dynafocal mount necessitating relocating both
top mounts slightly inboard to keep it symetrical.I am currently favoring a
gear driven supercharger by procharger with about 80" of manifold pressure
so the engine will match the drawing name----enough horsepower to do
something stupid-----. no guess as to horsepower but 1700 seems attainable

with the six rotor.The projected weight of the complete trex airframe and
engine is 1600 pounds with a 145 sq ft wing  area so performance should be
"adequate" And yes this can be a community project,  and the latest
revisions of the development crossections will be with the solid models. My
CNC router arrived today.  23" X 35" travel with 130 MM depth of cut. It
came from CNCjCut of jinan China. The factory was easy and cooperative to
deal with, it comes with arcsoft and arcCAM softwear. I opted for the linear
guides recommended to mill aluminum.I searched on ebay for       router
machines     and found them there.

george grimes

I don't think a six rotor is going to work George.
Too much torsional stress on the e-shaft. Stick to 4 rotors
or less.

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.