George,
Your comment about change in water flow charteristics when P-ports are
inserted in a large water passage is a pertient observation. I
calculated that hole area is over 4.5 cm2. Water flow in the coolant
system would have to reduce and/or the system back pressure increase to
maintain stock water flow when blocked. In affect it is like shutting a
downstream valve. I would think we want higher than stock flow through
the block as we are working the engine at higher power densities. Anyone
with access to the Mazda Racing housings could confirm the size of the
holes in the water passages to see if there is a difference between them
and stock housings.
Doug in Japan
With the sealing block system water can still flow around the SS p-port
tube. You don't have to pot the area with epoxy if you are concerned with the
water flow in that area. If you do pot it you may be able to drill
a 1/2 inch dia. or larger water passage. Another possibility is a small
external return line from the rear rotor housing back to the input to the rad.
This is common practice on Chev V8 racing engines.
I agree that robust water flow is a good thing.
The blockage is not that bad. You have to figure the percentage of the
total area blocked and if you look not at the rotor housing but at the
center housing you will find the center housing side ports block a lot
of the return water flow.
The bottom line is the metal temperature adjacent to both the wear surface
and the spark plugs explained in my book How to Cool Your Wankel.
Mark Steitle installed thermal couples in that location and found
the temperatures a couple of hundred F below the metal temperatures
in a Continental liquid cooled aircraft piston engine. I have tons of
data on this subject.
IMHO what is far more important is apex seal temperature which is affected
by rotor cooling and apex seal oil supply. Hot apex seals wear faster and
the apex seal slot itself wears faster. In fact the early RX8 with what
turned out to be inadequate oil supply to cool the apex seals resulted
in less than 100,000 mile life. Mazda addressed the problem by adding
additional oil injectors about 2007. I still add a 1/4 ounce of 2 cycle
oil to each gallon of gas in my 2004 RX8 along with the regular
metering pump.
Paul Lamar
Paul,
Thanks. You are correct. Looking at the sliced intermediate housing I see
what you mean. The remaining water passage is restricted.
Gee its a real wonder coolant manages to get where it needs to go with
all of those dead ends expanding and contracting chambers and convoluted
shapes. Kudos to Mazda to figure it out.
I suspect they are still figuring:)
Doug in Japan
I think they are too. I suspect the 16x is a total re think.
It was a guy by the name of Max Bentele working for CW that came up
with the serial cooling idea. NSU did it right from the get go just
like the OX5 parallel cooling system.
I can highly recommend a book by Herschel Smith called "A History of
Aircraft Piston Engines" published by Sunflower University Press Inc. 1531
Yuma, Manhattan, Kansas 66502-4228. ISBN 0-07-058472-9. 629.134'352 in a
good library. This is a reprint of a book originally published by McGraw
Hill in 1981. Fourth printing 1993. There are 250, 8.5 by 11 pages. It
chronicles the evolution of the aircraft engine from early days to the
present. There are many tables listing every engine ever put in an airplane
with all important specifications including weight, horsepower, RPM,
configuration and in some cases BSFC. There are many photos and drawings of
all types of aircraft engines. This is as close to a bible of aircraft
engine history that I have found so far.
http://www.rotaryeng.net/books10.html
Those that fail to learn from history are doomed to repeat it.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.