Subject: P-port water passages
From: Rotary Engine
Date: 8/9/2009, 4:22 AM
To: AAA Put this in the To box


 George,

Your comment about change in water flow   charteristics when  P-ports are
inserted in a large water passage is  a  pertient observation. I
calculated that hole area is over 4.5 cm2.  Water  flow in the coolant
system would have to reduce and/or the  system back  pressure increase to
maintain stock water flow when  blocked.  In  affect it is like shutting a
downstream  valve.  I would think we want  higher than stock flow through
the  block as we are working the engine at  higher power densities.  Anyone
with access to the Mazda Racing housings  could confirm the  size of the
holes in the water passages to see if there  is a  difference between them
and stock housings.


Doug in   Japan


With the sealing block system water can still flow around  the  SS p-port
tube. You don't have to pot the area with epoxy if you  are  concerned with
the
water flow in that area. If you do pot it  you may be  able to drill
a 1/2 inch dia. or larger water passage.  Another possibility  is a small
external return line from the rear  rotor housing back to the  input to the
rad.
This is common  practice on Chev V8 racing  engines.

I agree that robust water  flow is a good thing.

The  blockage is not that bad. You have to  figure the percentage of the
total  area blocked and if you look not  at the rotor housing but at the
center  housing you will find the  center housing side ports block a lot
of the  return water  flow.

The bottom line is the metal temperature adjacent to  both  the wear
surface
and the spark plugs explained in my book How to Cool   Your Wankel.

Mark Steitle installed thermal couples in that  location  and found
the temperatures a couple of hundred F below the  metal  temperatures
in a Continental  liquid cooled aircraft  piston engine. I  have tons of
data on this subject.

IMHO what  is far more important  is apex seal temperature which is
affected
by  rotor cooling and apex seal  oil supply. Hot apex seals wear faster
 and
the apex seal slot itself wears  faster. In fact the early RX8  with what
turned out to be inadequate oil  supply to cool the apex  seals resulted
in less than 100,000 mile life.  Mazda addressed the  problem by adding
additional oil injectors about 2007.  I still add a  1/4 ounce of 2 cycle
oil to each gallon of gas in my 2004 RX8  along  with the regular
metering pump.


Paul  Lamar

I just  checked some factory race Periphery Port housings. At the top of
the
port cavity is a 25/64" [.39"] hole for coolant flow. Just  one.

Lynn E. Hanover


Lynn

Very good. Thanks.  I  asked because my O-ringed insert PP tube
effectively blocks the water  passageway.  There is however enough room
near the outer top of the  passageway to remove some metal and allow
water to flow through.  I  take it the other cavities holes on the
return side are about the same as  stock?

Doug in Japan


I will check on that in the AM and get back to you.
Lynn E. Hanover


Paul, I had a notion on testing my waterflow once I make some parts. I am
going to bolt the parallel flow center housing to a rotor housing ond plumb
a garden hose to first the inlet and then the outlet and run the water into
a 5 gallon bucket to time how long  each side takes to fill the bucket with
flow through the rotor housing.I want to have slight back pressure from the
return water to even out flow distribution on the inlet side water. I came
up with a way to bypass/transfer the side housings so as not to restrict
flow through the rotor housings where seal cooling  might be improved.Look
on the rotor face side of the housings on the cast iron wear plate. The
solid models shoe a 1/8" thick blockage but that is removed with the
machining. Also all the part faces include a 3/16 inch machining allowance
which is taken off with the lathework. all the holes are cnc  milling
machined as are the ports.It seems lie a drilled hole through the potting
mix is good insurance if  only to purge air out of the cooling system or
trapped steam from the exhaust area below .

george grimes


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.