Subject: P-port water passages
From: Rotary Engine
Date: 8/9/2009, 12:35 PM
To: AAA Put this in the To box


George,

Your comment about change in water flow    charteristics when  P-ports are
inserted in a large water passage  is  a  pertient observation. I
calculated that hole area is over  4.5 cm2.  Water  flow in the coolant
system would have to reduce  and/or the  system back  pressure increase to
maintain stock  water flow when  blocked.  In  affect it is like shutting  a
downstream  valve.  I would think we want  higher than  stock flow through
the  block as we are working the engine at   higher power densities.  Anyone
with access to the Mazda Racing  housings  could confirm the  size of the
holes in the water  passages to see if there  is a  difference between them
and stock  housings.


Doug in   Japan


With the sealing  block system water can still flow around  the  SS p-port
tube.  You don't have to pot the area with epoxy if you  are  concerned
with
the
water flow in that area. If you do pot it  you may  be  able to drill
a 1/2 inch dia. or larger water passage.   Another possibility  is a small
external return line from the  rear  rotor housing back to the  input to the
rad.
This is  common  practice on Chev V8 racing  engines.

I agree that  robust water  flow is a good thing.

The  blockage is not that  bad. You have to  figure the percentage of the
total  area  blocked and if you look not  at the rotor housing but at  the
center  housing you will find the  center housing side ports  block a lot
of the  return water  flow.

The bottom line is  the metal temperature adjacent to  both  the wear
surface
and the  spark plugs explained in my book How to Cool   Your  Wankel.

Mark Steitle installed thermal couples in that   location  and found
the temperatures a couple of hundred F below  the  metal  temperatures
in a Continental  liquid cooled  aircraft  piston engine. I  have tons of
data on this  subject.

IMHO what  is far more important  is apex seal  temperature which is
affected
by  rotor cooling and apex seal   oil supply. Hot apex seals wear faster
and
the apex seal slot itself  wears  faster. In fact the early RX8  with what
turned out to be  inadequate oil  supply to cool the apex  seals resulted
in less  than 100,000 mile life.  Mazda addressed the  problem by  adding
additional oil injectors about 2007.  I still add a  1/4  ounce of 2 cycle
oil to each gallon of gas in my 2004 RX8  along   with the regular
metering pump.


Paul  Lamar

I  just  checked some factory race Periphery Port housings. At the top  of
the
port cavity is a 25/64" [.39"] hole for coolant flow. Just   one.

Lynn E. Hanover


Lynn

Very good. Thanks.   I  asked because my O-ringed insert PP tube
effectively blocks the  water  passageway.  There is however enough room
near the outer  top of the  passageway to remove some metal and allow
water to flow  through.  I  take it the other cavities holes on the
return side  are about the same as  stock?

Doug in Japan


I will  check on that in the AM and get back to you.
Lynn E.  Hanover

The stock 12-A rotor housings are wide open through the area that would
become the intake runner.

The center iron is blank between the two case bolt holes so no water would
pass through no matter what the rotor housing look like. The front and rear
irons have a passage below the case bolt hole that would be unused, so a
hole  above the runner would work.

The Pport housing has three interesting features that are not on the  stock
rotor housing.

The area where the runner is formed has a reduced thickness next to the
runner, and is rounded at the top to match the contour of the top of the
runner.  This would connect the front and rear irons flow wise through the .039"
hole.

If the unused case bolt hole and land is completely removed during assembly
and a path is left open above the runner, it would function as a stock
piece. If  the bolt hole land is left behind, the land could be notched between
the inner  wall and the land to provide flow. Or the land area could be
shortened on each  end.


There is a 1/8" notch in the case bolt lands above the runner, so some
flow would occur
and, or, would let air bubbles escape to the top of the housing.

Along the hot side the case bolt lands are severed from the inner housing
wall. Only the land area for the spark plugs connect the outer from the
inner  walls. The stock housing has all of the land areas connected to both
inside and  out side walls.

If you expose a bolt hole to coolant you must plug the unused case bolt
hole at least in the rear iron.

This is 12-A data and may not be helpful.

Lynn E. Hanover


I think that is .39" Lynn and not .039" :)


Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.