Subject: Another victim of the stimulus. For sale 3 rotor and RV10
From: Rotary Engine
Date: 8/10/2009, 8:13 PM
To: AAA Put this in the To box

 Bill bought it from Allan Tolle. He got one and I got one.
 I am not selling mine :)

 Paul Lamar

 Steve,
 As Paul said I got it from Allan Tolle, and he had removed all
 the manifolding but I still have it in boxes. I haven't done
 much to it other than turn it over and put in some top cylinder
 lube every month. It seems to be in good shape but I still
 planned to rebuild it prior to running.
 Bill Jepson


 Hi Bill
 Sorry about the job, just got shelved myself after 32-years at Boeing,
 glad I did my own investing and didn't bite the latest financial
 bullet.  Very interested in your engine, is it a p-port or a new
 configuration ?  Still learning about rotaries and their differances.
 Also considering remote turbos has any one experimented with them ???
 thanks, doc

 Doc,
 Sorry it took so long to get back to you, the message got burried in a
 stack of e-mail. My 20B was a standard Cosmo Automotive unit. Designed for
 progressive turbos. Alan told us that these units had been bought by Mazda
 R&D in
 SoCal as test units just before Ford closed the unit down. They were going
 to be crushed! He and an inside connection rescued a couple. As Paul said
 there were 2 He got one and I got the other. The engine is a standard side
 port intake, p-port exhaust. Just like a 13B with an additional rotor.

  Regarding isolated turbos, I just returned from the Evergreen Aircraft
 museum (home of the Spruce Goose) in McMinnville Oregon, I have family
 there
 and I was job hunting. They have a super looking P-38 and B-17G both of
 which
 have super long plumbing to the turbos. You could do it on the rotary with
 only one worry. The exhaust temperature of the rotary would make it tough
 to
 plumb long runs without causing high temps in the cockpit. Otherwise the
 idea of plumbing the turbos downstream sounds fine. you would need an oil
 schavenge pump to return the oil to the sump, or tank.
 Bill Jepson

Doc, the thing about remotely mounting a turbo is that any losses in
exhaust gas temperature reduce the available volume of exhaust flow thru the
hot side of the turbo. You are going to want 321 stainless, ceramic coated
on the inside and outside and  use the insulating wrap to reduce radiation
losses. Also minimize bends and bend radius as much as possible.

the
compressor to engine plumbing is relatively less critical but suffers the
same performance penalty of aero drag from  pipe length and bends.  I use a
performance loss of 15% for every 90 degree elbow as a rule of thumb for
evaluating possible pipe runs. This skews the results to the conservative
side.

Mazda got turbocharging really right with the turbos basically bolted
to the exhaust port. The problem with the stock turbos is  that they are
sized for sea level operation, and when the air gets thinner at altitude
(less dense) there is less drag on the compressor impeller allowing it to
speed up past the  RPM limits on the bearings resulting in bearing failure.

This comes from several people I have met who tried it and forum postings on
the internet. In race cars we can size the compresor side of the turbo
smaller for throttle responce or larger for maximum mass flow as the turbos
two sides bolt together in the center housing and are interchangable for a
particulardesign series.  This option is not readily available on the mazda
due to it being too close to the engine.


By all means if you do remote
mountig put an inercooler in the compressor side plumbing to increase charge
density which is a good tradeoff on the drag due to going thru the
intercooler. We  tend to build high performance airplanes which have good
power at take off and don't need major supercharging at seal level. I
suggest that you size the compressor to turbo-normalize which is a way of
keeping sea level HP at altitudes such as 8000 feet and little boost at sea
level.I spent an afternoon with Bruce Turentine (the mazda rebuilding video
sold thru RWS) an he told me his experience with 13B turbo engines has been
reduced engine time between overhauls. The problem was chatter
marks(washboarding) of the rotor housing after loss in tension of the two
flats springs under the apex seal in the rotor. He is of the opinion that
continued operation with the turbo  raising back pressure on the engine
causes heat soak of the rotors not encountered with intermittant turbo boost
in the car and the flat spring sets get anealed allowing the apex seals to
skip on the running surface.

Also of prime importance with turbos running
continuously on boost is that they get very hot on the exhaust side. Mild
boost puts them at 850 degrees (black heat) and serious boost turns them red
hot at about 1340 degrees. You can't wrap the turbos and force the heat to
stay in as they get hotter yet, so heat shields to dissipate radiant heat
would be in order.If anyone out there knows of  successful turbo instalation
that is kiting out the parts how about a posting on the newsletter.

george grimes

Good article George.

Dave Leonard has been flying for awhile. There are others.

Check out.
http://www.rotaryeng.net/dave-interview.mpeg
http://www.rotaryeng.net/best-flyover1.mpg
http://www.rotaryeng.net/low-roll-short-clip2.mpeg
http://www.youtube.com/watch?v=CYmpAIJWykU&feature=channel_page
http://www.youtube.com/watch?v=2iSzGqirbsI

What fails at altitude
is the blades come off the turbine. That has happened at least five times in the past
eleven years. The turbine is way too powerful and some way must be found
to slow it down.

If chatter and loss of temper in the apex seal springs becomes a problem
go with ceramic apex seals as they don't transfer heat as well as iron.
Also increase the supply of apex seal oil as that is what keeps the
apex seal cool. You could also try squirting more oil into the rotor
to cool it better.

Here is a pdf of a magazine article I just found on turbo's.
What I like about it is they give the diameters of the turbines and compressors.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.