Subject: twin pusher project reduction drive
From: Rotary Engine
Date: 8/19/2009, 5:07 PM
To: AAA Put this in the To box


 Good morning Paul

 I am sending you a sketch the way i am looking the
 reduction angle drive with all components ,check it and come back on
 your own view


 Jean Prudhomme

 Nice sketch Jean.

 I took the liberty of modifying it the way I think it should be done.

 IMHO using u-joints on the prop shaft adds unnecessary weight and
 torsional flexibility.

 It is up to you of course.

 Paul Lamar

 Jean Prudhomme wrote:
 Paul what are you doing for the reverse trust when engine is lost and
 prop dragging on the air stream crating a reverse trust on propshaft??

 How are you attaching the prop flange to the main carbon fiber tubing??

 Jean Prudhomme

 The carbon fiber prop flange would be bonded to the carbon prop shaft.

 About the only practical thing to do is find an electrically adjustable prop that
 will feather. I don't think you are going to come up with a workable hydraulic
 constant speed featherable prop system with this arrangement of angle drives
 and carbon fiber shafts.

 If you make everything out of steel to tolerate the oil 200F temperature it will be a
 huge weight penalty. As a I said before put two engines on the wings and talk
 Mistral into selling you a couple of constant speed gear boxes and forget it :)

 Perhaps Jeff Doddridge can build us a planetary constant speed prop gear box
 like these 3D's.

 Paul Lamar


 On the picture below as lyc, main bearing-cs-with housing

 Do you have some dimentions on this design i like it the way it is and we
 can had a spline shaft at the end to go on the std spool,

 Jean Prudhomme

 It is based on a stock Lycoming front main bearing whatever size that is.
 I don't have one to measure it. It is a copy of the front end
 of a Lycoming engine.

 It is designed to be attached to a stock Mazda high pressure die cast
 light weight bell housing and used as a planetary gear constant
 speed prop PSRU just like a GITSO.

 I don't recommend it for your application because it will be way
 too heavy and way too torsionally flexible when you add flanges,
 splines, U-joints, tapered roller bearings, stock spools and shafts.

 You would also need to beef up the aft part of the nacelle to take the
 650 foot pounds of local bending loads due to gyroscopic reactions
 from the heavy constant speed props when the aircraft is stalled or
 rapidly yawed due to turbulence. This will add a lot of airframe weight.

 A long one piece large diameter carbon fiber prop shaft drastically reduces
 the local bending loads on the structure due to prop gyroscopic reactions.
 Only much smaller lateral and vertical loads would occur near the prop bearing.
 The helicopter bearing in the custom angle gear box with the custom spool
 takes out the much lower loads due to this gyro bending reaction.

 IMHO the only way to make your layout practical is cut the number of parts
 and use a long one piece carbon fiber prop shaft incorporating the custom angle
 reduction drive and spool on one end and the prop flange on the other. But that
 is just me and the way I would do it.

 Paul Lamar


 How you will support the prop carbon shaft the fact you can,t use embedded
 oil housing for lubrification.

 The way i see it is building an housing with light weight std spool
 and lubricate with oil circulation similar to the Mark-18 and then
 use the carbon fiber shaft with spline at the end of spool and the
 other end with sealed bearing so the carbon shaft will orerate on
 dry atmosphere.

 I am guessing i might be 10 to 20 heavier then tracy gearbox but
 the plane will handle it


 Jean Prudhomme

 "10 to 20" Kg or pounds? My guess it will be at least 50 pounds
 heavier for each drive. Tracy's drive now weighs about 45 pounds.

 BTW Tracy's gear box can be machined to lose
 a bit of weight. However Tracy would be the first to tell you it
 is not strong enough to take a 50 pound constant speed hydraulic prop.

 I was planning on a secrete, oil pressure fed, experimental, light weight,
 Teflon lined plain journal bearing. (Patent applied for):)
 Separate low pressure cool oil supply with an electric oil pump.

 Stretch over oil seals.

 Paul Lamar

Paul

Thank,s for the infos

Do you have the tracy prop shaft dimentions and weight

Jean Prudhomme

It is out of the box but it is up at the hangar.
Which dimensions are you  interested in?
The prop shaft with bearing weighs 9.25 pounds.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.